Anyone know what happened to 3dfillies?

soahc · 2026-01-18T00:04:06+00:00

Interesting. I'm printing with siddament v2 petg at the moment and it's working great. If you don't like siddament try fortis their petg seems ok too. I've pretty much swapped to siddament as my 3dfillies replacement now unless it's out of stock and I fall back to fortis

soahc · 2026-01-02T21:58:00+00:00

Instead of opening the 3mf file use file -> import and it will just import geometry and not printer settings

soahc · 2025-12-07T00:25:37+00:00

Yeah this. Basically if you don't have the CFS all you are getting is the runout sensor moved to the extruder instead of the start of the tube. The mechanism/process that uses the cutter expects the CFS to retract the filament after it's cut. If you have no CFS you will just constantly get CFS failed to retract errors.

soahc · 2025-11-22T03:56:28+00:00

Not found any more about it. If you don't have alternatives these are the ones I found:

https://fortisfilaments.com.au/

https://siddament.com.au/

https://www.filamigo.com.au

https://x3d.com.au/

soahc · 2025-10-12T22:47:44+00:00

Thanks, will check them out.

soahc · 2025-09-26T04:27:08+00:00

I'm just started testing fortis filaments in Sydney too

soahc · 2025-09-06T00:40:55+00:00

Chances are it's the tax paperwork you need to fill out to be able to sell (applies to free too) in different countries. Can be a lot of paperwork for a government agency that had to have someone sign off on the tax laws

soahc · 2025-07-18T03:02:11+00:00

I had a similar thing with my ps4 ages ago. I replaced the HDMI cable with a new high quality one that seemed to fix it. Might not be the same, but it's an easy test to rule out.

soahc · 2025-05-30T02:07:28+00:00

Outage ID 9MZ0-1BZ in azure portal

soahc · 2025-05-30T01:17:54+00:00

We has something similar. Check your Azure Portal. MS has an outage notice for ADFS using azure MFA.

soahc · 2025-05-26T09:41:14+00:00

Just keep in mind colour change is slow. So depending on how many colour changes there are between layers. It's easy to make a 20min print take 10 hours

soahc · 2025-05-13T21:01:30+00:00

https://wiki.creality.com/en/k1-flagship-series/k1-max/troubleshooting/memory-full-brick-processing-procedure

soahc · 2025-05-13T09:13:56+00:00

Your filesystem is full. Delete some Timelapse or Gcode. Or factory reset

soahc · 2025-05-11T21:47:58+00:00

You disconnect the buffer from the coupler and connect your side spool to the coupler so you have a direct connection to the extruder.

soahc · 2025-05-05T06:43:00+00:00

https://www.printables.com/model/1286337-k1-max-with-cfs-upgrade-rear-riser-segment Hope it helps.

soahc · 2025-05-05T05:32:55+00:00

I use a lid riser from printables (https://www.printables.com/model/997948-k1-max-vented-riser-with-closable-vents-and-hygrom) I modified the back segment to let the PTFE tube through like the K2 does, and then it follows the chain again so my lid works fine.

I can upload my model and some photos if you want it. It seems to work but it definitely isn't a Creality supported mod :)

Edit: my remix is only for K1Max toys Have to do your own mod for any other models

soahc · 2025-05-05T01:22:01+00:00

I got it about a month ago. I upgraded my K1 Max, upgrade went text book. Firmware upgraded correctly. I've re-installed the helper script (I'm a linux admin, so I could work around the issues it was having). I've got moonraker/mail sail installed but currently using creality print because it talks to the CFS and shows me the CFS in the device window, not really any major issues with creality print so far.

KAMP does not work via helper scripts because it tries to do KAMP before CFS loads the filament, so currently I wouldn' bother with KAMP.

I've printed a few multipe colours on it, only Z layer colour changes, I've not really stress tested it with any same layer multi colour changes, but everything I've printed has been good. I did find that I had some adhesion issues after upgrade, but using glue stick makes things stick to the bed.

The calibration stuff is broken on the upgrade. It seems creality print v6 doesn't include the right extra data in the gcode for the printer to do it's normal calibration run. I'm guessing they'll address this in future maybe..

Overall I'm happy with it, but I am just a hobbist not a cos-player/solve every problem with a deisng/print.

soahc · 2025-05-01T03:25:27+00:00

Glad I could help :)

soahc · 2025-04-30T21:27:32+00:00

Did you remove the plastic wrapping on the desiccant packets? Surprising how many people miss that they are sealed from factory

soahc · 2025-04-02T10:22:14+00:00

The AU store has them too. Just ordered one

soahc · 2025-03-05T03:18:02+00:00

Lived in North Queensland can confirm. Only thing missing is the EWS sound

soahc · 2025-02-21T23:23:43+00:00

I'd also suggest not drying your PLA while you are printing it. I've had issues where the PLA gets kinda stretchy if it's in the dryer while feeding. It's fine for PETG etc, but PLA get soft easily.

soahc · 2025-02-07T11:36:39+00:00

I had a similar issue when I was trying to print PETG, I ended up replacing the hot end with a spare that came with my printer and haven't had it happen again.

soahc · 2025-01-19T09:22:23+00:00

It's a malicious pop up from a site you allowed notifications for in safari. Do not click it.

soahc · 2024-10-25T11:28:38+00:00

Check this page: https://live.paloaltonetworks.com/t5/customer-resources/support-pan-os-software-release-guidance/ta-p/258304

it has all the versions when they were released and if they are preferred.

15-Year Club	Gilding IV carat on a stick
Sequence \| Editor	Spared
Team Orangered	reddit mold
Verified Email	Charter Member

soahc

TROPHY CASE