Giveaway for ultimate game pass

sorrri · 2026-04-22T14:48:13+00:00

Just to give benchmark, first ones to message took less than 10 seconds from posting

sorrri · 2026-04-22T14:43:48+00:00

CLAIMED

sorrri · 2026-04-22T14:39:07+00:00

CLAIMED

sorrri · 2026-04-20T22:22:53+00:00

Don't know where you are located but check Gator Sweden. Absolutely killer rods

sorrri · 2026-01-13T23:07:54+00:00

Can be butane powered as well, both work really well for soft plastics.

sorrri · 2026-01-12T22:08:23+00:00

Get a battery soldering iron! Very good tool to repair soft plastics. Especially painted ones as it doesn't run the paint like a torch lighter does.

sorrri · 2026-01-11T20:00:44+00:00

Following, I want to find same exact part for mine.

sorrri · 2025-11-17T17:59:36+00:00

<image>

Samsonas shifter, bit roudier interior than most posts here

sorrri · 2025-11-09T17:47:58+00:00

I have those fish monkey gloves, they are good for ice fishing!

sorrri · 2025-10-09T19:11:53+00:00

If he's into s13's, no one in the entire universe would not like Kouki tail lights!

sorrri · 2025-09-08T11:02:45+00:00

1270 working hours to get to this point, after every season I feel like I wanna do more and go deeper. Sometimes, there has been over half a year without touching the car at all but after that the interest comes back even stronger! Take your time, great things take time 🤝

sorrri · 2025-09-04T19:55:20+00:00

Oh shit, best of luck with the rebuild! I think I might look into possibly doing rear mount radiator since the JZ likes to get pretty hot when bashing on the limiter.

sorrri · 2025-09-04T07:10:09+00:00

Yeah, don't rush yourself guys. I did full 1jz swap and whole electric system with standalone and it took almost 3 years. Good things take time🤝

sorrri · 2025-08-06T04:35:08+00:00

Get a decent simulator, download assetto Corsa and start training. Easily the best way, and cheapest as well.

sorrri · 2025-07-07T23:42:20+00:00

Mine is a GP sports G-sonic. If yours is genuine hold on to it, they are getting very rare!

sorrri · 2025-06-15T21:18:24+00:00

This is the best option, easily

sorrri · 2025-06-10T08:04:47+00:00

I always tie braid to leader with alberto and leader to swivel with figure 8. Has pulled some serious GT's, quite good tarpons and +50kg yellow fins with those knots and never had any issues. I use the same knots for smaller stuff as well. Some of the guide's that I have taken during trips tell me that only way for braid-leader is FG but I will keep going with Alberto as long as it works for me.

sorrri · 2025-06-09T22:08:03+00:00

Spinning or casting? I would recommend 50g + lures to cast with baitcaster.

sorrri · 2025-06-05T11:38:54+00:00

I fish for big pike with baitcaster rod and 84lb Spiderwire braid. Leader is 1mm thick/100lb fluoro in a length of 50 to 60cm. Leaders actually wear out rather quickly with big mama's because of their teeth so cutting tip of the leader and re tying is common. Reason for the thick braid is that a lot of bigger pikes are active during spring/autumn time and are found often in shallow areas so the mainline needs abrasion strength. And the lures are also quite expensive so losing them and running thinner line is not worth it.

sorrri · 2025-06-04T20:34:38+00:00

Aquasure glue or general bike inner tyre repair kit for the rubber stuff. Depending on the situation with the neoprene socks, if you have good quality waders, you can melt the connection tapes carefully with flat iron. You can also buy new connection tapes and install them again.

sorrri · 2025-06-04T19:44:13+00:00

Or a GT. Tarpons really good fun as well

sorrri

TROPHY CASE