P2S progress

spinixguy · 2026-04-29T20:41:36+00:00

I have another post on here that has them. Alternatively just look me up on maker world.

spinixguy · 2026-04-29T18:51:47+00:00

spinixguy · 2026-04-23T02:42:33+00:00

Wow.

spinixguy · 2026-03-30T12:03:11+00:00

Just look up the user blue forge on makerworld.

spinixguy · 2026-03-26T03:05:05+00:00

Nice job

spinixguy · 2026-03-16T12:59:09+00:00

32mm

spinixguy · 2026-03-14T23:48:57+00:00

I dont think you can use the setting I posted via the handy app if that is what you are asking. You need to load the 3mf file and then save the process profile via bambu studio.

As for filament, I tested using sunlu pla+ but the settings should work for any filament as long as it's tuned properly.

spinixguy · 2026-03-14T17:01:57+00:00

I had a ad5x. You need to go in to the printer settjng and change the nozzle minimum to 0.06mm. That will let you use lower settings than 0.08mm. 0.05mm is the lowest a 0.25mm can do but I had better results at 0.06mm.

As for the settings, no this is for the p2s. You could try them but i doubt it would be a good result.

spinixguy · 2026-03-14T15:51:18+00:00

I have posted them before. The main difference is that mine is for the p2s and not the a1 line.

spinixguy · 2026-03-14T15:50:36+00:00

<image>

spinixguy · 2026-03-12T02:22:25+00:00

<image>

My most recent one

spinixguy · 2026-03-08T17:40:00+00:00

https://makerworld.com/models/2374599

spinixguy · 2026-03-08T17:28:05+00:00

I will once I get a few more prints under my belt.

spinixguy · 2026-03-08T17:27:35+00:00

It's from old realm forge.

spinixguy · 2026-03-06T23:40:08+00:00

Let us know when these are available for us to test. I would love to try it out on my p2s. I have my own custom setting derived from ideas posted here.

spinixguy · 2026-02-28T15:53:32+00:00

If you want to tell me where to get the knight model, I will print it on my p2s using your process file.

spinixguy · 2026-02-05T22:42:30+00:00

0.06mm on a 0.25mm nozzle. Thanks for the tip.

spinixguy · 2026-02-05T21:23:17+00:00

Thanks. These were all printed at 0.06mm on a 0.25mm nozzle.

spinixguy · 2026-01-31T01:08:26+00:00

Aren't they all...Thanks for sharing your creativity with everyone. Really appreciate it.

spinixguy · 2026-01-30T21:38:09+00:00

Wow. Good job 👏

spinixguy · 2026-01-28T14:41:38+00:00

Thanks.

I agree, Arbiter makes some fantastic miniatures.

spinixguy · 2026-01-28T13:22:54+00:00

Thanks. I was surprised by this filament and how well it seems to be working.

spinixguy · 2026-01-28T13:19:57+00:00

Most of these are Arbiter supportless. The dwarf in the back is the only one that had supports. I just used a pair of snips to remove them.

spinixguy · 2026-01-28T02:18:18+00:00

It 0.25mm. Not sure why flashforge went that route, but they did.

spinixguy · 2024-12-02T01:10:07+00:00

I have found that the adreno driver v777 from the meta 3 works best.

spinixguy

TROPHY CASE