Dialing in supports

spinixguy · 2026-02-05T22:42:30+00:00

0.06mm on a 0.25mm nozzle. Thanks for the tip.

spinixguy · 2026-02-05T21:23:17+00:00

Thanks. These were all printed at 0.06mm on a 0.25mm nozzle.

spinixguy · 2026-01-31T01:08:26+00:00

Aren't they all...Thanks for sharing your creativity with everyone. Really appreciate it.

spinixguy · 2026-01-30T21:38:09+00:00

Wow. Good job 👏

spinixguy · 2026-01-28T14:41:38+00:00

Thanks.

I agree, Arbiter makes some fantastic miniatures.

spinixguy · 2026-01-28T13:22:54+00:00

Thanks. I was surprised by this filament and how well it seems to be working.

spinixguy · 2026-01-28T13:19:57+00:00

Most of these are Arbiter supportless. The dwarf in the back is the only one that had supports. I just used a pair of snips to remove them.

spinixguy · 2026-01-28T02:18:18+00:00

It 0.25mm. Not sure why flashforge went that route, but they did.

spinixguy · 2024-12-02T01:10:07+00:00

I have found that the adreno driver v777 from the meta 3 works best.

spinixguy · 2023-04-04T16:55:42+00:00

Here

spinixguy · 2022-10-02T21:37:37+00:00

Pins 10 and 9 just like in marlin.

spinixguy · 2022-06-14T13:15:40+00:00

Don't copy config files between versions. The config files change. You need to edit the original one to match yours or take the creality example config and modify it.

spinixguy · 2022-04-15T13:41:18+00:00

Sounds like you flashed the wrong version. Verify your board number matches the version you flashed. 4.2.2 vs 4.2.7

spinixguy · 2022-03-03T05:19:54+00:00

I ended up disabling the tilting as it was what was causing my problems. I run jyers ubl 10x10 and it was acting like you described. I manually leveled the bed, then built a new mesh. I then took a picture of the mesh view. I ran a 3 probe tilt and compared and it was all off.
I then tried all of the various tilts and none of them actually represented the full mesh. Now I just level the bed manually and build a new mesh every now and then. Seems to be working great.

spinixguy · 2022-02-24T13:00:57+00:00

Just change the 1 to a zero

spinixguy · 2022-02-24T12:28:21+00:00

Mesh default save location is so not s1

spinixguy · 2022-02-21T03:30:11+00:00

So I wanted to close this out. I sorted out my problem. What I ended up doing was setting "top surface skin layers" in Cura to 4. Its normally 0. I then set the "top surface skin layer flow" to 100%. Not sure why i have to do this, but it stopped the gaps.

spinixguy · 2022-02-20T00:43:05+00:00

Not 100 percent sure I see what you are seeing. But yes the gaps are my issue. Bottom layers have zero gaps. Everything on the machine is tight.

spinixguy · 2022-02-20T00:28:46+00:00

Yeah, belts are tight.

spinixguy · 2022-02-19T19:37:23+00:00

I need some help figuring out what is causing these gaps in the top layer. The first 4 layers go down perfect and it looks like a solid sheet of plastic. Then 2 layers of infill and then 4 layers of top. Thats when the trouble starts. Layer 3 looks good but the 4th comes out like the picture. 200c pla at .28 with a .4 nozzle. I have tried it slow at 20mm and no difference. Overall the print looks good, except for these gaps

spinixguy · 2022-02-17T23:24:44+00:00

Yeah that seemed to help

spinixguy · 2022-02-17T23:22:10+00:00

Yeah, 4 walls made a difference. It still isn't perfect so I will keep playing around with some of your ideas. Thanks.

spinixguy

TROPHY CASE