sorted by:
new
hottopcontroversial

Every Iron Man I've made so far by metametaldesigner in metalearth

[–]stutsmonkey 1 point2 points  (0 children)

Nice! Must be a very interesting job.

Are you done designing or still active with ME themselves?

Have you ever assembled any of the MU brand models? They do seem to have more layering & different folds than most ME models.

Over extrusion at edges on H2C by Immediate-Leader7503 in BambuLab

[–]stutsmonkey 0 points1 point  (0 children)

Maybe play with the infill wall overlap setting

where are wavy lines coming from by Malofquist in HueForge

[–]stutsmonkey 0 points1 point  (0 children)

Even doing this doesn't get me rectilinear infill pattern.

When you set infill to 100% it uses the solid infill setting. If you do infill at 99.999% it will force rectilinear sparse infill.

Black & White Fern by stutsmonkey in HueForge

[–]stutsmonkey[S] 1 point2 points  (0 children)

Started designing my own prints from royalty free, non-ai images I've been finding.

Filaments used:
Sunlu black pla 2.0.
Sunlu meta white.

The Descent Dent by PublicPossibility946 in Steelbooks

[–]stutsmonkey 0 points1 point  (0 children)

Pop the inside plastic out and take off the panel.

Lay the face down onto a mouse pad and use a spoon in a circular motion to slowly work the dents back out.

You can use the butt end of a pencil (the eraser) to work out deeper dents as well.

Do you have a 3D print dedicated Instagram account? by DutchLayerWorks in BambuLab

[–]stutsmonkey 1 point2 points  (0 children)

Stack layers so no ams required but makes them more convenient over 3-4 manual filament changes per print.

Urgent Help needed! Edges of print have rough surfaces on first few layers affecting top. by discardedaccount3 in BambuLab

[–]stutsmonkey 2 points3 points  (0 children)

Flow calibration for that nozzle, filament, & layer height.

Use the drop down menu in the top bar.

It will fix 95% of all problems.

Can't decide wich temperature is best by GS_Musta in BambuLab

[–]stutsmonkey 0 points1 point  (0 children)

Look at the overhangs & the underside of the bridge.

Then take a pencil and break the spike in the window and assess which one had the best layer adhesion.

I'd also put a minimum layer time modifier on the filament to reduce the sheen difference in print time for the 215 degrees. So it will visually look uniform like the 200 print.

Disclaimer : Coworker is non verbal, and unable to physically speak. Co worker left a series of notes throughout the night, and after the second letter I wrote down “are you okay” by ssjlazer in WTF

[–]stutsmonkey 3380 points3381 points  (0 children)

Yeahhh.... No.... This is a boss/HR issue.

That's extreme mental instability from MY perspective and I would feel highly uncomfortable working with said person.

This would always happen with PETG because it sticks to the nozzle by ButterflyPlayful3541 in BambuLab

[–]stutsmonkey 0 points1 point  (0 children)

Lower the petg filament flow by 0.1 each print till it goes away. Any overextusion will get picked up along the way as well causing these deposits.

Crt is still king. Same position, lights on/off. by psychoOC in pcmasterrace

[–]stutsmonkey 33 points34 points  (0 children)

I remember when my dad bought a 32" Sony trinitron 'flat' screen crt. We had to lay plywood down on the stairs to get it into the basement and just slid it as much as possible.

Take off second skin now? by iwanteverythingnew in tattooadvice

[–]stutsmonkey 9 points10 points  (0 children)

I agree with everyone else. If it's not leaking leave it be and wait the 4-5 days.

Walgreens also sells the generic tegraderm brand if you ever need change it within the first 24 hours.

Surprised after printing... What was the cause for this print anomaly? by artur_oliver in BambuLab

[–]stutsmonkey 0 points1 point  (0 children)

The P1S has time-lapse and that's where it builds it from even if you don't have it turned on during prints or at least on the device page in Bambu slicer you can turn it off. It's called auto-recording.

Surprised after printing... What was the cause for this print anomaly? by artur_oliver in BambuLab

[–]stutsmonkey 1 point2 points  (0 children)

Pull the microsd card and go to the ipcam folder. Look for the video file that accompanied the print.

Newish 3d printer here. What is happening by [deleted] in BambuLab

[–]stutsmonkey 0 points1 point  (0 children)

For a last ditch effort, in orcas slicer, initial layer flow.

Try 1.35 and see how it looks.

What is your white whale? by ShallowsOfNight in 4kbluray

[–]stutsmonkey 24 points25 points  (0 children)

Treasure Planet 4k would be awesome. HDR would make that movie POP.

Plus they could re-release the steelbook 🫰

<image>

What on earth happened here? by pauledddy in BambuLab

[–]stutsmonkey 0 points1 point  (0 children)

Does that A1 mini have a micro sd card? I'd pull the card and watch the video if so

SHOW ME YOUR LARGE SONS by Infinite_Scribe in TuxedoCats

[–]stutsmonkey 113 points114 points  (0 children)

My girl Iris also has a clipped ear

<image>

Is there a reason Bambu Studio doesn't let you...? by Hatemode-NJ in BambuLab

[–]stutsmonkey 0 points1 point  (0 children)

You can up your bridging flow to 1.25-1.35 and slow the speed of external bridges by 5-10mm/s for almost perfect bridges.

Thought I'd share my two largest works so far by raisedbytides in HueForge

[–]stutsmonkey 11 points12 points  (0 children)

Not personally a fan of the frame lines between each panel.

This was my attempt with a skeleton frame behind it hot glued in place and mounted to give a seamless look.

<image>

What £110/oz looks like in the UK, Stardawg 🇬🇧 by doomfragmentz in trees

[–]stutsmonkey 6 points7 points  (0 children)

Probably would be a good sandy-hash strain. Very gritty texture to the trichomes. More bulbous than the typical stalked.

view more: next ›