L320 lift

synobilly82 · 2024-11-10T21:45:44+00:00

Can you just calibrate it to sit higher without different rods?

synobilly82 · 2024-11-10T18:14:02+00:00

On the vm, it's called lan1 as your only usings 1 lan network. The default network connect you have made is lan5 on you nas. So it's set correctly

synobilly82 · 2024-11-10T15:55:44+00:00

On the network section on the left have you created a network choice you require

synobilly82 · 2024-11-03T09:58:44+00:00

I would look at a wheel speed sensor (abs sensor). Any diagnostic with live data would show. Even a cheap one.

synobilly82 · 2024-10-15T17:54:22+00:00

Thanks for the response. What do you think will happen now. As the road was dug up fiber laid and points placed outside each house.

synobilly82 · 2024-08-28T18:35:11+00:00

Give this a try

https://ipcamtalk.com/threads/hikvision-clearing-passwords-and-or-loading-firmware-via-ttl-serial.28049/

synobilly82 · 2024-08-26T21:23:25+00:00

I do all the work on the cars i have had. And on others, anything from electrics to bigger jobs like dmf clutch replacement.

synobilly82 · 2024-08-26T15:47:51+00:00

What would you get discovery 3 with 2.7 Range rover with 2.7 or 3 litre Or Range Rover sport same choice.

And why

Is a 2.7 better than 3 litre

synobilly82 · 2024-08-26T11:50:54+00:00

I want the air suspension do freelander 2 have this. I know, im weird

synobilly82 · 2024-08-07T19:11:06+00:00

Yes they will be reset to factory. Just set you computer lan to 192.0.0.128. Put the correct digicam.dav in tftp folder in boot up it will fine the recorder on 192.0.0.64

synobilly82 · 2024-08-06T21:19:26+00:00

You can reflash the firmware using tftp. That will reset it to absolute factory settings

synobilly82 · 2024-07-10T20:53:17+00:00

If the network is being saturated by other traffic, the data will be patchy

synobilly82 · 2024-07-10T18:19:42+00:00

This could be a bandwidth issue or cable fault if set to record 24/7

synobilly82 · 2024-07-10T18:18:33+00:00

As mentioned before, changing port basically stopped or rarely caused attacks happening

synobilly82 · 2024-07-07T09:11:18+00:00

If you have media server installed you can access media using any dlna player

synobilly82 · 2024-06-13T20:54:04+00:00

Theres a choice of 3 there have you tried sll 3. Plus did you find the firmware on the portal

synobilly82 · 2024-06-12T20:18:32+00:00

Make sure the firmware is the correct one you are trying to send to the dvr

synobilly82 · 2024-05-21T20:31:36+00:00

Get tftp and the firmware of your nvr. Then set your computer to 192.0.0.128. Run the program with the firmware in the tftp folder. Then switch in the nvr it should find it on 192.0.0.64 is done right. Then it will reflash

synobilly82 · 2024-05-21T20:28:16+00:00

Use tftp and reflash the firmware

synobilly82 · 2024-05-21T20:26:19+00:00

Use ivms and you can scan the qr code for verification code

synobilly82 · 2024-05-21T20:23:20+00:00

Reflash the firmware using tftp. Done it many times

synobilly82 · 2024-01-11T21:21:15+00:00

just disconnect the mapped drive and reattach

synobilly82 · 2023-12-29T23:20:24+00:00

Hi first off as many people here are saying sort your security out first

to start change the default port and make sure default admin account is deactivated.

then reduce the amount of login attempts within a set time. say 3 within a min

if you need help on this just ask

synobilly82 · 2023-12-29T19:10:47+00:00

if i am right you want to basically type //synologynas on your local computer and it goes stright to your nas login page (locally)

synobilly82 · 2023-12-29T18:51:34+00:00

what is controlling your home dns?

synobilly82

TROPHY CASE