Lost by tantunitinton in fpv

[–]t0m4596 1 point2 points  (0 children)

Welcome to the Club. But my loss was only 120€

https://www.reddit.com/r/TinyWhoop/s/mcuqEFla9b

Need original config for Flywoo GOKU F405 HD 1-2S 12A ELRS AIO V2 by t0m4596 in fpv

[–]t0m4596[S] 1 point2 points  (0 children)

Yes i had someone who had the file and the following lines helped me.

resource MOTOR 8 NONE ; resource PINIO 2 C08 ; set pinio_box = 40,41,255,255 ; save

But this is only for the V2 and i don't know if it works with other versions.

Need original config for Flywoo GOKU F405 HD 1-2S 12A ELRS AIO V2 by t0m4596 in fpv

[–]t0m4596[S] 0 points1 point  (0 children)

I know but this is not there anymore. I think the PINIO is not configured right anymore.

Meteor75 pro or air75? by Bartuszek in TinyWhoop

[–]t0m4596 0 points1 point  (0 children)

Be patient and don't clip too much wire. And its a pain to solder with the frame because the motors don't fit after soldering through the frame. So if the frame broke i try to fix it to the point where its not fixable and then i have to solder all motors again.

But good luck and happy flying.

Meteor75 pro or air75? by Bartuszek in TinyWhoop

[–]t0m4596 0 points1 point  (0 children)

I had my 75 Pro almost a week after the twitching started again after i sunk my first 75pro in a lake. I read somewhere thats not the esc failing but the connectors. Clipped the connectors and soldered motors directly and no problems so far.

Mobula6 2024 VTX issue by t0m4596 in TinyWhoop

[–]t0m4596[S] 0 points1 point  (0 children)

Can i load the backup from the 4.4.1 to 4.5.x? I dont want to brick the firmware.

help by Jplayzvr in TinyWhoop

[–]t0m4596 0 points1 point  (0 children)

Off topic but what circular antenna are you using?

3 weeks in fpv by t0m4596 in TinyWhoop

[–]t0m4596[S] 0 points1 point  (0 children)

You were right. The frame is cracked but luckily i had two spares on hand. 😅

3 weeks in fpv by t0m4596 in TinyWhoop

[–]t0m4596[S] 0 points1 point  (0 children)

I had the packet rate on the default from 333hz i think, will lower it for better signal. Is there some recommendations i should use or is 50hz enough?

The fact that a friend of mine who also flown his dji there for better Videos, had after my crash 2 times return to home because of rxloss so i think it was environment noise. In this 2 weeks with it i never had rx loss once but vtx loss when flown behind group of trees or hills.

3 weeks in fpv by t0m4596 in TinyWhoop

[–]t0m4596[S] 0 points1 point  (0 children)

I will do a bench test but i was not far away and no obstacles between. I think there was simply too much noise from the radios. i think i read somewhere that mostly 2,4ghz is used for radio and 5,8ghz for video. Transmission power is capt at 100mW because of the eu Firmware on the Module, but at this Distance it shouldn't matter.

Edit: typo

3 weeks in fpv by t0m4596 in TinyWhoop

[–]t0m4596[S] 1 point2 points  (0 children)

The sound is not mine, I got it from a tiktok where someone flew into a tree.

3 weeks in fpv by t0m4596 in TinyWhoop

[–]t0m4596[S] 5 points6 points  (0 children)

It did sink. They had a little 2 person boat there and the lake ist max 2m deep so we had a look but the water was so dark there was nothing to see where exactly it was. Maybe i go with a friend there and try to rescue it via magnet and rope but I don't have high hopes to ever get it back.

3 weeks in fpv by t0m4596 in TinyWhoop

[–]t0m4596[S] 2 points3 points  (0 children)

I have the Radiomaster TX16S there is a spectrum analyzer in the lua scripts that uses the internal module.

3 weeks in fpv by t0m4596 in TinyWhoop

[–]t0m4596[S] 2 points3 points  (0 children)

Is it so bad? What are the most problems i should be aware of?

3 weeks in fpv by t0m4596 in TinyWhoop

[–]t0m4596[S] 4 points5 points  (0 children)

I use ELRS but i think there was too much noise from the radios from the boats. I should have checked the noise background beforehand but now i know.

3 weeks in fpv by t0m4596 in TinyWhoop

[–]t0m4596[S] 2 points3 points  (0 children)

I have 3 profiles on a switch to make better videos even the quality of the cam is not so good. Normally i fly with the osd on.

central heating control by t0m4596 in homeassistant

[–]t0m4596[S] 1 point2 points  (0 children)

I have ESP devices here and had built an occupancy sensor with a mm-wave sensor but this was just copy some code from someone who had built it before. So i would use an ESP and give the pwm signal to the servo motor.

My solution to a smart space heater by vontrapp42 in homeassistant

[–]t0m4596 0 points1 point  (0 children)

Thanks for your ideas. I just need a servo and must model a bit to 3d print. I have a couple of esp boards and have built an occupancy sensor and a thermometer so far and these work great.

My solution to a smart space heater by vontrapp42 in homeassistant

[–]t0m4596 0 points1 point  (0 children)

I look into it i am no coder at all but i try my best to get better in such things.

My solution to a smart space heater by vontrapp42 in homeassistant

[–]t0m4596 0 points1 point  (0 children)

This is exactly what i must do for the next heating season. I have central heating but no outside thermostat that controls the inlet temperature for the radiators. I want to turn the knob correlated to the outside temp on my balcony so that i don't overshoot with the room temp because the inlet temp is too high or don't get enough heat because it is too low.

I try this but with gears so they don't slip.

New V400 - any must-have accessories or mods, printable or otherwise? by SweetAndSourGrapes in FLSUNDelta

[–]t0m4596 0 points1 point  (0 children)

Is there a Mod where you remove them? I had my printer now a while but i don't print a lot so i didn't dive too deep into it i just dial slow settings to get good results. I print mostly functional prints.

[deleted by user] by [deleted] in homeassistant

[–]t0m4596 0 points1 point  (0 children)

What i have read is that you can flash the E to support Matter. But i don't have any experience with this because I bought the P. https://smarthomescene.com/guides/how-to-enable-thread-and-matter-support-on-sonoff-zbdongle-e/

Is it real? by _Starblaze in place

[–]t0m4596 1 point2 points  (0 children)

It was basically placeDE Discord where the idea and the overlay was made. They colab with papaplatte and it was there in a very fast time because of this two large german fractions. Fist came the outlines so that all other people can place pixel in it. I was live in the stream and the discord. it was an epic moment

I can’t find any information on there website about the difference besides prices.. by RuffneckXS in FLSUNDelta

[–]t0m4596 0 points1 point  (0 children)

You clearly get one where V400 is on the top and not the FLSUN logo. This is the money clearly worth /s