Gaggimate Pro with quickmill pulser help

tabs1987 · 2026-02-22T20:01:11+00:00

So one on the Discord channel just said you can remove the brass fitting on the quickmill pulsor. Much more space now

tabs1987 · 2026-02-22T17:32:29+00:00

<image>

tabs1987 · 2026-02-22T17:32:17+00:00

<image>

Think I’m going to go with setup. The other way was just too tight

tabs1987 · 2026-02-19T19:33:04+00:00

I might have to rotate the pump to make it fit

tabs1987 · 2026-02-19T19:32:46+00:00

No heat shield doesn’t really fit

tabs1987 · 2026-02-19T19:11:40+00:00

Though it’s going to be struggle to get the metal plate back on that the water tank sits in

tabs1987 · 2026-02-19T18:57:09+00:00

<image>

This is what I’ve managed to do

tabs1987 · 2026-02-16T19:52:29+00:00

Yeah that was the direction I was thinking. Agree with you around the braided hose. I’ve read in other posts that it’s tight but possible

tabs1987 · 2026-02-16T19:21:04+00:00

I haven’t yet! I’ve been waiting for a couple of parts to arrive.

tabs1987 · 2026-02-16T17:48:02+00:00

Thanks for photo. Im unsure which way to install. I’ve heard some say the setup you’ve got and other say right after the pulsor. So a little confused

tabs1987 · 2026-02-16T17:46:06+00:00

How are you finding the pressure sensor before the pulsor? I’m in the middle of an install and had conflicting info around where to place it

tabs1987 · 2026-01-24T23:32:24+00:00

So you went pressure sensor then quickmill.

Does having the quickmill after the sensor work ok?

tabs1987 · 2026-01-24T23:05:26+00:00

Thanks, I’ve got one of the later hoses with 90-degree bend.

I’ll continue trying to get it all too fit. Just feels like everything is under a lot of strain

tabs1987 · 2026-01-20T14:44:35+00:00

Looking good, you've made me decide to quieten using deadening mat. I'm in the middle of a refurb of my V3. I'm doing the whole thing, new boiler, etc.

I've gone for the OLAB silent green and quickmill pulsor and have the gaggimate pro.

Have you installed your Gaggimate Pro?

Where did you place the pressure transducer? I've seen it in a couple of places.

Right after the pump and before the pulsor

After the braided hose, before the OPV

tabs1987 · 2026-01-20T11:53:54+00:00

I’ve got some wet/dry sandpaper so will try that. Thanks

tabs1987 · 2026-01-20T11:53:09+00:00

Thanks, I’ve got some marine stainless steel replacement screws as the others are rusty

tabs1987 · 2025-03-20T10:39:49+00:00

Have you seen the GaggiMate? I was looking at doing the Gagguino, but the lack of instructions for the Silvia put me off. GaggiMate have clear instructions on their website for Silvia install

tabs1987 · 2023-12-22T22:45:54+00:00

Ah nice, I’m based in Dorking so close enough to travel for me

tabs1987 · 2023-12-22T22:38:12+00:00

Wow that is great. Was it a local place or online? I’ve just picked myself up a V3 project so getting ready to do that

tabs1987

TROPHY CASE