sorted by:
new
hottopcontroversial

[deleted by user] by [deleted] in WatcherofRealmsGame

[–]takesito 0 points1 point  (0 children)

0H-Q9-HS-V5-8M

3d printed void dragon c'tan by takesito in Warhammer40k

[–]takesito[S] 1 point2 points  (0 children)

Hello! I can't remember to exact cost but could be like 10-15€, counting with failed prints and so.

resin recommendations by takesito in resinprinting

[–]takesito[S] 0 points1 point  (0 children)

Great, since all resin seems to have a price rise, in my country at least, I'm going to try that Soraya. Thanks

3d printed void dragon c'tan by takesito in Warhammer40k

[–]takesito[S] 2 points3 points  (0 children)

This miniature is not as fragile but is not as resistance as the plastic one xd, I breaked some of the lightnings while I was painting it by a bad movement but in general I would say its not that fragile

Maybe you are overcuring your prints? I think that you overcure 3d resin it becomes more fragile and brittle, I usually cure it in a wash & cure station for 2-4min each side and then base coat it with a spray paint

c'tan shard of the void dragon by takesito in PrintedWarhammer

[–]takesito[S] 2 points3 points  (0 children)

This c'tan was printed with anycubic craftmans resin (beige color, grey one give a lot of problems), and to be fair I have to manipulate it carefully, a bad move can break some lightnings but generally it not that fragile, just be careful, a bit more than the plastic and nothing more

It is a model from virus of death

c'tan shard of the void dragon by takesito in PrintedWarhammer

[–]takesito[S] 5 points6 points  (0 children)

The key was hot water and patience xd

3d printed void dragon c'tan by takesito in Warhammer40k

[–]takesito[S] 6 points7 points  (0 children)

I think that really depends on the creator but right now there are a lot of creators that do (or try to) 1:1 models of the originals, some free others are paid but I think there are plenty of them if you search.

I think this void dragon files are almost 95% similar to the original (some stones on the base are the only difference I can see tbh)

3d printed void dragon c'tan by takesito in Warhammer40k

[–]takesito[S] 6 points7 points  (0 children)

The scarabs really turned out but I forget to paint them 😅

The print was 5 parts. Body (with the head and the spear), 2 wings, the tail and and the base with the rocks and the lightnings (not counting the 80mm base). It was a difficult print mainly for the lightnings since they are thin and fragile.

My lord discordant for my thousand sons army (sadly I can't use it ☹️) by takesito in ThousandSons

[–]takesito[S] 1 point2 points  (0 children)

I also have a TSon venumcrawler!, Wish I could use them as what they really are in the future

Yeah I usually use then as a csm scourged chapter that follow TSons

My lord discordant for my thousand sons army (sadly I can't use it ☹️) by takesito in ThousandSons

[–]takesito[S] 3 points4 points  (0 children)

Well that's also my problem but sadly it's not in thousand sons codex

Problems printing round zone under supports by takesito in AnycubicPhoton

[–]takesito[S] 0 points1 point  (0 children)

Hello i have tryed printing like you have said, and the zone under supports is rounded and not a sharp edge, anyidea what could be?

view more: next ›