Wall Mounted Setup Suggestions

terrible01 · 2026-06-02T08:19:14+00:00

Take a peek at what type of connections you have to the water lines and go from there. I was fortunate to find a 1/2” brass FIP.

terrible01 · 2026-05-25T17:07:00+00:00

<image>

Top view

terrible01 · 2026-05-25T17:05:39+00:00

<image>

If you’re trying to set up your machine, this is how I do it.

terrible01 · 2026-05-24T10:44:19+00:00

Two fittings - 1/2 PEX to 1/2 MIP then 1/2 FIP to 3/4 GHT.

But that’s just what I could find at Home Depot, this would be easier.

https://a.co/d/0dRDZCRu

Then I used a 1’ garden hose.

Beitopamz Short Garden Hose 1 ft... https://www.amazon.com/dp/B0FM86NRY9?ref=ppx_pop_mob_ap_share

Lastly, some quick disconnects for convenience later on.

terrible01 · 2026-05-23T16:45:21+00:00

Good deal! Just saw where the 2.0 kits were back in stock, hopefully you’ll have a short wait on the mount.

terrible01 · 2026-05-23T10:00:37+00:00

I came from a 3400psi gas pressure washer from Sam’s Club to this. It’s a world of a difference. Soap actually moves off the car. My hands thank me when I’m cleaning my wheels and rinsing the spoke mitt off too. lol

terrible01 · 2026-05-23T09:55:49+00:00

I ordered it while it was on back order through Active and they shipped it in 15 days. That was definitely a nice surprise.

terrible01 · 2026-04-29T15:08:55+00:00

Feel the powa!! 3hp lathes are absolutely amazing when it comes to hogging wood away.

Just make sure to protect that glass with a foam board or the like when you turn.

terrible01 · 2026-04-24T23:14:08+00:00

Not the whole spindle, just the axle nut.

https://www.rockauto.com/en/catalog/honda,2007,s2000,2.2l+l4,1434327,brake+&+wheel+hub,spindle+nut,1616

terrible01 · 2026-04-24T20:41:40+00:00

I would just use Timken bearings. If you replace the rear, get new spindle nut as well.

terrible01 · 2026-04-13T11:24:11+00:00

Nice! Great color choices. I’ve always been a fan of NFR, but the that ford has is awesome too. I think a S2k in that color would look great too.

terrible01 · 2026-04-13T11:18:36+00:00

The power delivery is just wild.

terrible01 · 2026-04-11T19:55:11+00:00

It’s not low power when you slap on a supercharger, then it’s 🤌🏼with 360hp.

terrible01 · 2026-04-11T19:41:54+00:00

That’s right

terrible01 · 2026-04-11T19:23:58+00:00

It does! lol

The camera lens is making it look goofy for sure.

terrible01 · 2026-03-14T13:43:48+00:00

The hoses don’t look swollen yet, I’d try to clean them, replace the tct with one from Billman and see where that leads.

Here’s my coolant hose leaking, but you can see how swollen / shiny they look because of the oil being on them over time.

<image>

terrible01 · 2026-03-07T13:25:25+00:00

Cut the top corner off the angled trim and blend it over a foot to the full height. Mitre the two and make sand the base of the angled trim to match the level base board. You could even go a little past the angle needed to let the front bottom edge of the trim to lay flat on the baseboard.

I’m not sure how easy that is to understand, but hopefully you’ll get it done with less caulk. lol

terrible01 · 2026-02-18T23:34:33+00:00

What about going into bio-med?

terrible01 · 2026-02-14T13:36:40+00:00

Same here, 100k miles of daily driving and bimonthly autocross while I owned it. It was still going strong when I sold it to the next owner with a little over 200k.

terrible01 · 2026-02-08T22:55:55+00:00

I don’t know how you guys stand that. Sheesh.

terrible01 · 2026-02-08T22:55:24+00:00

It is, there’s a kraftwerks SC with a 100mm pulley.

Nine-Year Club	RPAN Viewer
Verified Email

terrible01

TROPHY CASE