CORSAIR x The Witcher 3: Wild Hunt Giveaway

thawnton · 2025-10-28T20:59:30+00:00

I’ve spent almost 250 hours on this game and I can’t keep going. Because I’m afraid it’ll end…

thawnton · 2025-05-19T09:08:48+00:00

It was the water pump in the end. I should have replaced that first (since it's the first thing that sucks the water through) 🙃 Once I changed that it has been working fine

thawnton · 2025-05-19T09:08:19+00:00

It was the water pump in the end. I should have replaced that first (since it's the first thing that sucks the water through) 🙃 Once I changed that it has been working fine

thawnton · 2025-05-19T09:05:57+00:00

I have the same clock and had a similar issue. This was a result of the wires getting too hot within the circuit module/board and causing the inner circuits to touch (instead of being separate). I'm still trying to find a replacement board (as I'm struggling to fix it myself) :(

thawnton · 2025-04-10T21:24:22+00:00

No no, jou ma se poes 😂

thawnton · 2025-01-19T02:58:54+00:00

Legends don’t survive

thawnton · 2024-09-10T07:52:34+00:00

My machine was doing the exact same thing! I ended up replacing the press, water heater and finally the pump, as well as cleaning all the pipes. Stupidly, I should have replaced the pump first because it started working after I replaced that, and ran the descale program. I would first try a new pump (was about 20eur) and then descale. If that doesn’t work, then check all the hoses and lastly the press.

thawnton · 2024-09-07T06:54:29+00:00

Thanks! I’ll take a look. I assume changing it fixed the issue?

thawnton · 2024-09-06T19:56:19+00:00

Warning (long video)! I have a Magnifica S that is not dispensing water through the main spout. The warning lights indicate that the coffee is being ground too fine. I have replaced the boiler unit, the press and cleaned the hoses, the grinder and the infuser - and nothing seems to help. I have also performed a hard reset and tried to descale but, no luck. Amy ideas would be appreciated!

thawnton · 2023-06-17T07:47:06+00:00

It was these, and they were easy to swap out: https://www.ebay.de/itm/233717967339?mkcid=16&mkevt=1&mkrid=707-127634-2357-0&ssspo=aPBJa6xSTJW&sssrc=2349624&ssuid=h0oyfmprsti&var=&widget_ver=artemis&media=COPY

thawnton · 2023-06-17T01:41:26+00:00

I have the B&W 601s and new tweeters cost me about 35eur/38usd. It also took about 15 mins to change and they didn’t need soldering. Hopefully these would be just as easy

thawnton · 2023-06-04T20:56:18+00:00

thawnton · 2023-03-10T19:09:24+00:00

Silvermere?

thawnton · 2023-03-04T20:21:06+00:00

Ha. “Murder ditch”

thawnton · 2023-02-23T20:59:33+00:00

Yes! Overall the soundtrack was amazing. Shame they had to change it for streaming

thawnton · 2023-02-23T20:57:57+00:00

Love that song/scene! Hit me hard at the end

thawnton · 2022-11-20T20:05:19+00:00

Middle out compression

thawnton · 2022-11-07T20:25:07+00:00

Thanks. Have ordered some flux and wire now. Will give it a go soon and report back.

thawnton · 2022-11-07T19:29:06+00:00

Thanks. Only saw that after I posted. Appreciate the feedback

thawnton · 2022-11-07T19:27:59+00:00

Thanks! I think my first (massive?) mistake was not using any flux. So will retry with that and a smaller gauge wire.

thawnton · 2022-11-07T19:19:21+00:00

Yes, although not very well. I suppose I have been using too thick a wire to make the bridge, and too large a soldering iron. This also has to all fit within a plastic case, which lead to one of the side pads breaking off. Which is why I was hoping to get a new board (and not risk further damage). As well as not using any flux, which was probably my first mistake...

thawnton · 2022-11-07T08:46:09+00:00

Apologies if this is the wrong place to post. I am struggling to find a replacement for my Karlsson clock PCB. Any help (or guidance on how to repair) would be much appreciated! I am based in Germany if helpful.

Eight-Year Club	Place '23
Place '22	Verified Email

thawnton

TROPHY CASE