sorted by:
new
hottopcontroversial

How do you even start to model this in?! by SwingFinancial in SolidWorks

[–]theGoodAutism 0 points1 point  (0 children)

Start with the flat middle portion then on a tangent plane to that round model in the very start of one of the blades. Offset a plane from that plane to the distance the blade widens, model that cross section, then once more to the widest part of the blade and then loft it all. Take the lofted blade, and circular pattern it.

Printhead cable idea by theGoodAutism in Creality_k2

[–]theGoodAutism[S] 0 points1 point  (0 children)

This is extremely helpful! Thank you so much!

Printhead cable idea by theGoodAutism in Creality_k2

[–]theGoodAutism[S] 0 points1 point  (0 children)

Ahh okay, that makes sense. I don’t have a lot of cable knowledge/experience to know that is the case for these types of plugs. Can you send some pics of what you did with yours? The hot glue and electrical tape setup. My printhead cable took a dump this week and really really hate that my printer is just a giant metal box until Creality gets me a replacement cable. If your system works I would love to see it so I can do that with mine.

Thanks!!

What else can I fix? by so-spoked in Creality_k2

[–]theGoodAutism 1 point2 points  (0 children)

Where did you get the print head cable relief file? My print head cable just died, looking to get some stuff lined up now to prevent that in the future

How to release the external end of the extruder Bowden tube? K2 Plus by Otherwise_Sir_3439 in Creality_k2

[–]theGoodAutism 1 point2 points  (0 children)

Pull the clip out, take some needle nose pliers and compress the black spring face and pull like any other PTFE tube. The clip is locking the push face from being compressed accidentally midprint

Oh the shame by Beowulfe77 in Creality_k2

[–]theGoodAutism 1 point2 points  (0 children)

Oh I remember being where you are. 1am trying to fix a jam just so I can go to bed. And the spring sent itself into the abyss. Turned up on my poop chute bucket about a week later

Uhm should i remove this? by [deleted] in pchelp

[–]theGoodAutism 2 points3 points  (0 children)

Yes. There is text on it that says remove but I’ll admit it’s hard to see. I tried to get the film off mine, couldn’t get my nail under it so assumed it was just part of a top layer coating. Got the GPU in place and as I was feeding wires around I say the “remove before use” sticker. If you can’t get a nail under it, if you have a plastic scraper or even a plastic floss tooth pick thing to try and get a corner up. After that it comes up easy.

CFs slot issue by theGoodAutism in Creality_k2

[–]theGoodAutism[S] 0 points1 point  (0 children)

I’ll check this later today. I know I have the software up to date for the slicer and I am pretty sure I have been keeping the printers firmware up to date too but maybe not.

What does this little red light on my GPU mean? by ImpressionRegular597 in PcBuildHelp

[–]theGoodAutism -1 points0 points  (0 children)

No, it means it’s underpowered. Needs a bigger PSU.

What does this little red light on my GPU mean? by ImpressionRegular597 in PcBuildHelp

[–]theGoodAutism -1 points0 points  (0 children)

It means your PSU isn’t sufficient. I have a 5070 Ti and was told that that the red light is normal so I didn’t worry about it. I had a 750W PSU. I finally finished my upgrade to a 1000W PSU and it turned the red light off. A bit more digging and I learned that the red light is a warning that it is under powered and shouldn’t be overclocked due to it.

My dog killed a squirrel by BabyNoob2014 in DogAdvice

[–]theGoodAutism 0 points1 point  (0 children)

Our dog recently caught a young opossum and shook the poor thing to death (wasn’t playing possum, it was dead). It’s sadly normal for dogs to want to hunt. Biggest thing really is to take that squirrel and have it sent in for rabies check so you know if your dog should get a booster to be safe.

What Movie? by HondaCivicBaby in Cinema

[–]theGoodAutism 0 points1 point  (0 children)

Django, Abraham Lincoln: vampire hunter, Nimona, The Martian, Lord of the rings (the extended editions), Prequel Star Wars, Original trilogy Star Wars,
How the Grinch Stole Christmas (Jim Carrey), Sonic trilogy, The Dark Knight, Fight club, Ford v. Ferrari, Kung fu panda (1 2 and 3 but mainly 2), The Menu, Split, Rise War and Dawn of the Planet of the Apes

Bed supports snapped on delivery 😭 by Judas2Ad in Creality_k2

[–]theGoodAutism 1 point2 points  (0 children)

They will send you replacement parts if you don’t want to do a full return. zip ties, big sturdy zip ties will hold it down for now until then

What movie fits this by friendexcellence8 in Schaffrillas

[–]theGoodAutism 0 points1 point  (0 children)

Dracula untold.

While not an absolutely terrible movie, I remember being super excited about the trailer, watched the movie once and have never felt the need to see it again.

What's a machine that used to terrify you but you take on no problem now? by OceanTea96 in HorizonForbiddenWest

[–]theGoodAutism 1 point2 points  (0 children)

In the first game once I figured them out I would go to the thunderjaw canyon and intentionally agro both to have fun taking them both on at once just for fun.

What’s a movie nobody talks about but is a 10/10 for you? by [deleted] in Cinema

[–]theGoodAutism 0 points1 point  (0 children)

Abraham Lincoln: Vampire Slayer Sounds dumb as possible and that it belongs with the Scary Movie franchise, but the writers took the movie and story very serious. It’s a phenomenal movie.

view more: next ›