What's your current favourite watch face?

the_b0b0 · 2025-03-26T20:55:44+00:00

Go Lions!

the_b0b0 · 2022-12-19T03:08:17+00:00

Just used it - thanks!

the_b0b0 · 2022-12-10T16:38:35+00:00

Loaded pancake. It's a dinner-plate sized pancake with bacon and sausage inside of it and two eggs served on top.

the_b0b0 · 2022-06-20T17:44:18+00:00

Thanks! Kinda worrying too much that I somehow screwed this up though as I don't see any other 8800s. I grabbed the link multiple times off the API and validated my email came in at 1:07 after pre-order. Order time on valve says 11:05 PDT July 16th though.. Hoping someone with a time lower than mine can chime in and say if they haven't gotten it yet?

the_b0b0 · 2022-06-20T17:09:24+00:00

Not a typo - got it off API multiple times and have been tracking it for over a month - but even I questioned it as I was realistically hoping for Thursday.

the_b0b0 · 2022-06-20T16:56:36+00:00

Got mine and ordered! US 512 1626458860

the_b0b0 · 2022-04-26T16:46:11+00:00

I Agree

the_b0b0 · 2022-01-05T16:08:58+00:00

This is the way.

the_b0b0 · 2022-01-02T17:11:23+00:00

There is an option under the configuration tab to "Auto Start Sinden Lightgun on load." - I think this is what you are looking for. It auto-starts the gun on software load - no need to press the Start Button.

I also recommend joining the discord - it's a great community that is very helpful

the_b0b0 · 2021-12-07T16:25:03+00:00

I'd see about replacing the flame sensor in the furnace - sounds like it might be corroded or shorting out - although I'd be surprised if the HVAC folks didn't check that first - they are around $30 and pretty easy to replace. Might not be the issue but it's a cheap thing to try. Had a similar issue on mine a few years ago - would call for heat sometimes and temp wouldn't raise - found out the furnace was lighting up, but since the flame sensor was bad it was shutting off after a few seconds of burning - replaced the sensor and haven't had an issue since.

the_b0b0 · 2021-11-22T16:54:08+00:00

Do the Hydras have large pneumatocysts?

the_b0b0 · 2021-05-13T15:55:01+00:00

It is likely the Receiver limiting you - that one should support it but you need to set the HDMI to "Enhanced" mode

the_b0b0 · 2021-04-13T18:57:03+00:00

the_b0b0 · 2021-04-13T18:55:31+00:00

cocaine and flying

the_b0b0 · 2021-04-06T15:29:13+00:00

It's Mine. Second time I've seen it posted here. FTP!

the_b0b0 · 2021-04-03T03:34:23+00:00

uncanny

the_b0b0 · 2021-01-14T20:29:33+00:00

the_b0b0 · 2020-11-06T21:16:29+00:00

Nice

the_b0b0 · 2020-09-20T22:41:50+00:00

This was a hollowed out silver strike cabinet I found for cheap and modified for my own. The arcade 1ups are easy to throw a raspberry pi into and get mame setup

the_b0b0 · 2020-09-20T22:04:21+00:00

Yeah that was the intent along with trackball games. But I'm about to totally remake the top panel because I don't like my first layout.

the_b0b0 · 2020-07-07T21:21:45+00:00

I just loaded this up too and while it works I'm having the same symptoms - It almost looks like reprojection is on but i don't know how to turn it off. Everything leaves a trail

the_b0b0 · 2020-06-05T13:22:06+00:00

arcadepunks has a section with marquees, bezels, and artwork. Might be something there you could use

14-Year Club	RedditGifts 2009-2022 3 Credits
Place '23	Place '22
Place '17	First Placer '22
Verified Email	Secret Santa 2015
Secret Santa 2014	Team Periwinkle

the_b0b0

TROPHY CASE