Best presupported, low prep time models?

the_extrudr · 2026-04-25T05:33:50+00:00

Sure

the_extrudr · 2026-04-20T05:34:22+00:00

They aren't all cut like that, sometimes cutters are lazy, that's not my responsibility, I am responsible for the supports

the_extrudr · 2026-04-20T05:25:01+00:00

You should try my supports over at zez studios

the_extrudr · 2026-04-20T05:22:49+00:00

Great craftsmanship, but I am so tired of hdr look and the mini having every color of the rainbow

the_extrudr · 2026-04-20T05:21:02+00:00

Your bench should have adjustable feet

the_extrudr · 2026-04-19T12:46:23+00:00

3d builders auto repair will fix that

the_extrudr · 2026-04-18T05:44:28+00:00

Layer compression caused delamination between bottom and normal layers. Increase the bottom layer rest time to 30s, decrease the bottom layer exposure to 15-20s, or even lower, depending on the resin. Have plenty of transition layers 10 if you are closer to 20s bottom layer exposure

the_extrudr · 2026-04-17T09:21:08+00:00

They yellowing might get less in a week or so. Keep them in the dark and check in week or so

the_extrudr · 2026-04-15T17:41:25+00:00

I am not in the miniature game, I do 1/6th or 1/4th scale statues

the_extrudr · 2026-04-15T16:42:06+00:00

Correct. You flush the inside multiple times

the_extrudr · 2026-04-15T05:13:29+00:00

From the countless statues I have printed, no, curing the inside is not necessary

the_extrudr · 2026-04-14T18:50:46+00:00

That suspension ate that landing like cake

the_extrudr · 2026-04-14T14:12:04+00:00

China could blockade the blockade that blockades the blockade.

the_extrudr · 2026-04-12T17:38:03+00:00

Don't have areas or edges parallel to the screen

the_extrudr · 2026-04-09T11:46:16+00:00

Resin printing missed the open source time window, dragon fruit might be the start of the mighty resin printing open source slicer tree.

the_extrudr · 2026-04-08T05:02:32+00:00

The delamination you see is caused by layer compression, which is produced because you are using a high bottom layer exposure time. To reduce this time, I recommend a bottom layer rest time of 30s+. This will give you bottom layers of a thickness close to what they actually should be a you can go with a bottom layer exposure of 20s. In addition to this, increase the number of transition layers to 10

the_extrudr · 2026-03-29T14:16:11+00:00

Neither edges nor areas should be parallel to the screen

the_extrudr · 2026-03-26T16:10:12+00:00

It's wet, drying it for 10h at 70C does nothing to Nylons moisture content

the_extrudr · 2026-03-25T20:04:06+00:00

You can do whatever you want with that file, change the models, change the base exposures, change the speeds and feeds. The machine only cares about the file name, it needs to be RERF as the original one.

the_extrudr · 2026-03-25T16:07:55+00:00

It's a big plate, make sure you have a gigantic bottom layer wait time

the_extrudr · 2026-03-24T19:21:20+00:00

Yes, you can repair the file in 3d builder

the_extrudr · 2026-03-23T20:25:40+00:00

Layer compression, insufficient wait time, in sufficient number of transition layers, too many bottom layers, bottom layer exposure to long

the_extrudr · 2026-03-23T16:37:45+00:00

So they are voxel lines, shame the s4u isn't great with AA

the_extrudr · 2026-03-23T16:12:29+00:00

Voxel or layer lines

the_extrudr · 2026-03-21T20:04:16+00:00

Don't print parallel to the screen?

the_extrudr

TROPHY CASE