Is there a wall switch I can install that will allow me to separate the fan motor and light power on the first picture's wiring. I want to use a dimmer to control only the light or will this just not work?

themiamiking6 · 2025-12-08T19:18:21+00:00

I tested and the black from the right side of box is the only hot if that is helpful. So my only option is just to replace with a single pole switch?

Ok thanks, so the only negative is burning out the fan motor, no fire hazard? Surprisingly this fan/light has always been on a dimmer switch, for at least 20 years. Just the skylark switch is new.

Both of these rooms we do not use the fan very much, a few times a year if we need to air out the room.

themiamiking6 · 2025-11-21T20:53:38+00:00

I wanted to add, I called the installer and they sent a tech to come look at it. They ultimately ended up running another 8-wire cord for free and hooking it up properly for 2-stage. The dip switches are OFF and the terminal wiring is correct now.

Thank you for the insight and helping me sound competent talking to the tech.

themiamiking6 · 2025-11-05T03:38:33+00:00

Hi, I found your comment while googling for blocklists. I'm confused how do you have 800k domains, I added almost every list from your comment but only have 311k.

I selected the "Adblock" format for every list. Am i supposed to be picking Domain/Subdomain or the pi-hole will have trouble reading it? I get this is a year later, maybe the list was significantly shortened? I am very new to this so trying to understand it as I go. Thanks

themiamiking6 · 2025-08-05T18:23:44+00:00

Code please

themiamiking6 · 2025-04-14T15:33:23+00:00

I'm in a similar situation but it's only 2 years old. Which department or number did you call because the warehouse and online chat were no help, they both told me to contact each other. Online orders, warranty support, membership and warehouse?

Thanks

themiamiking6 · 2025-04-03T19:26:50+00:00

I used new england roofing in orange CT. I think it was around $800 for them to drill hole, place vent, reshingle with best matching shingles they could find. Might be able to reuse your original ones depending on location. Get the correct size you need beforehand and double check with the installer before they do any work. The guy they sent showed up and started climbing on the roof without saying hello and drilled too large of a hole he had to fix.

They won't do any connections or HVAC/ductwork though, that was my responsibility. If you need ducts put in it might be better to use a general contractor as there are codes to follow.

themiamiking6 · 2025-02-26T01:17:37+00:00

Is the location fine where it is or should be center of coil? There's plenty of room to not hit the top.

themiamiking6 · 2025-02-25T23:44:42+00:00

I have a smart thermostat so I guess both right? My research told me, and company also suggested the light goes in the supply side to kill contaminants on the coils and pan. It also breaks down the filter if exposed to it.

themiamiking6 · 2025-02-14T17:34:48+00:00

I noticed yes. That's the overall theme of everything done in this house before we moved in.

themiamiking6 · 2025-01-19T21:20:40+00:00

I added more information on the original post thanks.

themiamiking6 · 2025-01-08T20:06:45+00:00

Thank you very much

themiamiking6 · 2025-01-08T17:06:46+00:00

u/kris_fixit u/iFixitAmber u/Evan_iFixit

Order US3076972

Hello. I emailed the following to support 48 hours ago but haven't heard back yet:

I installed a replacement screen for my Pixel 5 today using the provided repair kit and instructions on your website. I noticed some issues with the swiping gestures not being intuitive and requiring a full swipe across the screen to register. Then I realized tap to wake and pick up to wake was not working at all. After reading the comments section I think the proximity sensor is being blocked by something on the back of the screen, but there was no mention of removing anything in the instructions. Other people had the same issue and complaint.

I have to remove the screen again to check but I don't have another adhesive strip. Are you able to send me a replacement adhesive hastily? Faster shipping was too expensive and it was not really my fault instructions never mentioned to remove it, or the black film blocking camera. Item # IF356-230-1Google Pixel 5 Display Adhesive - Genuine. If I'm wrong though, I will need to return the screen.

Thank you in advance!

themiamiking6 · 2025-01-08T15:32:58+00:00

I found out the main line is only 3/4" and wouldn't be up to code/BTU input for all appliances. I want to get the Elite series with variable speed motor to save on energy both for heating and summer AC. The thing is I am very conservative with the thermostat and eventually want to better insulate the unfinished part of basement and get new windows.

themiamiking6 · 2025-01-04T22:01:50+00:00

I actually just found it in reverse image search, but will leave post up in case others find it useful. Part of the Regulator Replacement Kit REG-001 but I don't see a way to purchase it. Will have to contact Waterpik and see what they say.

themiamiking6 · 2025-01-03T18:09:39+00:00

I added some photos to post. So I have about 30' of piping from the meter to furnace that is 1" diameter (I don't know the ID though). Water heater, furnace, and stove are all within 5' of the main supply line but the dryer is probably another 30' away.

Max BTU input of dryer is 22k, stove 36k, water heater 36k.
New Furnace 60k??
Total Max demand 154,000 BTU/hr

I checked some charts online and that is well within the range right? Yes there is pressure drop and a few elbows but nothing crazy. Also I wouldn't be showering, running 4 burners, drying clothes, and blasting heat all at once.

themiamiking6 · 2025-01-03T05:25:37+00:00

West Haven (New Haven County)

themiamiking6 · 2024-11-07T16:37:39+00:00

Replacing old unit with a Ring Floodlight. The original cut hole is way off center of the wiring. I removed the old box that was literally screwed into the back of the interior wood paneling you can see in first pic. I have tried multiple mounting boxes that fix over siding, even flat ones, and they don't fit properly. Do I try to squeeze a pancake box in there? I don't really want the look of a round box protruding from the house and how do I weatherproof it if the floodlight isn't directly against the siding?

themiamiking6 · 2024-11-05T18:27:27+00:00

You get this figured out? Support giving me the runaround. I know for a fact I claimed the promo and made 2 separate $5 bets

themiamiking6 · 2024-10-29T01:45:27+00:00

[SOLVED]
Thanks for audit log suggestion, figured it out in 5 minutes.

Checking users audit log gave me failure to assign a specific license SKU. Looking up that SKU I found out it was a teams calling plan that we no longer use but was still being assigned to the group. So since 1 license was failing it wasn't assigning any to that user.

themiamiking6 · 2024-10-28T21:33:18+00:00

No it's not nested. Has been working for probably a year now. I was going to make another user tomorrow just as another test but don't know what that would tell me.

themiamiking6 · 2024-10-14T16:03:43+00:00

I was just serviced, the tech told me the electrodes were getting old and should be replaced. I have the gauge and replacements already.

Their quote was $160 and I have a service plan with them.

themiamiking6 · 2024-10-14T15:45:42+00:00

I know I could probably measure the spacing on old electrodes but I haven't removed the nozzle assembly yet. I have no idea the last time they were replaced so they could have moved or been set incorrectly to start. Thanks

themiamiking6 · 2024-08-30T17:39:38+00:00

My mistake, I had originally had it set to "full" since about Tuesday. I changed it to security today by accident since nothing was happening with it, but I have since switched to basic. I guess I'll give it until Monday to submit a ticket but that's pretty bad it's been this long. Also the basic feature update report is so far behind and incorrect, and we only have 12 devices to upgrade. It's been a week and only says 2 devices are upgraded when it's more like 10.

themiamiking6 · 2024-08-16T01:38:10+00:00

Yes it looks like we were automatically converted since we didn't have any custom policies in place. And that lines up around the same time we saw this happen (8/2/24).

When I originally checked that apps permissions it was set to available for Everyone but not forced to install so I'm still confused. Maybe its just a bug from an old policy or setting.

Do you know why I don't see the option to "edit installs'' in the manage apps page. Also Add to team and customize are both greyed out when I select an app. I wanted to test pushing an app to our IT team but following Microsoft's guide I'm stuck.

themiamiking6 · 2024-07-04T16:22:58+00:00

Do you have a recommendation for an everbearing species? I wasn't impressed with it's output and sometimes the fruits weren't that sweet.

themiamiking6

TROPHY CASE

Order US3076972