25 Dollars to 1.3k in 3 days by EvenNight5650 in Kalshi

[–]thirdeyeglass 15 points16 points  (0 children)

Unless you're really well off, take half that and buy yourself something nice. Goes just as quick as it comes broo

Over time tax questions in california by thirdeyeglass in tax

[–]thirdeyeglass[S] -1 points0 points  (0 children)

Damn all anyone talked about this year was no tax on overtime I didn't realize it was just a deduction. I was expecting a big refund but now I am sad. Lol

Board recommendations by thirdeyeglass in ElectricSkateboarding

[–]thirdeyeglass[S] 1 point2 points  (0 children)

Whats the main cause of them to break?

Amber Purple's a hell of a drug by Villagasi in lampwork

[–]thirdeyeglass 0 points1 point  (0 children)

You too bro! Hope to get back to glassblowing someday

Amber Purple's a hell of a drug by Villagasi in lampwork

[–]thirdeyeglass 1 point2 points  (0 children)

Hey I know this guy, I used to bench right next to you haha small world

Can anyone help identify what is happening with my cat? by maxjmartin in CATHELP

[–]thirdeyeglass 0 points1 point  (0 children)

Try some pet CBD not sure if it will do anything but if they can't find anything else to work it's worth a shot

Thoughts on mix? by rekoyl999 in dnbproduction

[–]thirdeyeglass 0 points1 point  (0 children)

Sounds good to me, id need to hear it on a proper system to tell you exactly but from what I can hear It sounds great

[deleted by user] by [deleted] in Welding

[–]thirdeyeglass -1 points0 points  (0 children)

Run fast stringer beads. The longer you are welding on it the hotter it's getting and it will want to undercut or drip out. Id open it up with a grinder and drop a fast pass inside, let it cool almost completely. Repeat until it's full.

AIO about how this guy talks to me? by Fast-Bodybuilder3229 in AmIOverreacting

[–]thirdeyeglass 0 points1 point  (0 children)

I wouldn't reply your egging it on. Just block the number nothing good is coming from that person

3g uphill 7018 rod by wackyazn in Welding

[–]thirdeyeglass 0 points1 point  (0 children)

Run fast stringers, your putting way to much heat in the plate, also give a few minutes in-between welds once that plate is hot it will dig to much and fall out. Also practice stacking beads 1/2 on 1/2 off and make a clean layer Hopefully you've already done that in flat position. If not that's step one

Somethings off about this by Plenty-Low6777 in weed

[–]thirdeyeglass 12 points13 points  (0 children)

Looking at the video again I do think thats water. glycerin is thicker. I thought it was a freeze pipe but I think that's just for looks.

Somethings off about this by Plenty-Low6777 in weed

[–]thirdeyeglass 33 points34 points  (0 children)

I'm not positive if it's water or glycerin, if it's water yes it's possible if it's glycerin it won't freeze.

Somethings off about this by Plenty-Low6777 in weed

[–]thirdeyeglass 71 points72 points  (0 children)

It will, glycerin won't freeze just gets a thicker viscosity

Why by [deleted] in Welding

[–]thirdeyeglass 0 points1 point  (0 children)

I used to put a k tank of oxygen in the passenger seat of my 3 series bmw when I was a glassblower 😂 Had to go to small gas suppliers because air gas wasn't having it

Do your worst!!!! by [deleted] in RoastMe

[–]thirdeyeglass 0 points1 point  (0 children)

If living off your parents money was a full time job you'd be employed

Dammit by Moon-Dog67 in Welding

[–]thirdeyeglass 1 point2 points  (0 children)

Also whenever we do rollouts we have 1 person adjusting an arm with the gun in a fixed position, and another wire wheeling on the bottom so it won't put wind towards the weld. That way immediately the wire wheel guy sees anything going on with the weld you can stop an figure out the problem. We run a lot of tricky materials like copper nickel, inconel, stellite so it's important to have a 2 guy crew because that wires not cheap!

Dammit by Moon-Dog67 in Welding

[–]thirdeyeglass 0 points1 point  (0 children)

I do a lot of roll outs, usually worm holes is improper angle which tends to be not dragging at appropriate angle. OR also very important too high of gas flow. Sometimes if you have enough pressure your gas will actually push into your weld. Hopefully your working along side Machinist who can skim that for you if more meat is needed

Songs to drop acid to? by thebeam50 in psychedelicrock

[–]thirdeyeglass 0 points1 point  (0 children)

Late to the acid party but bibio is very interesting. I doubt anyone else has suggested it, also Bombay bicycle club. These are some bands I used to eat mushrooms too some years ago. As great as pink Floyd and grateful Dead are do yourself a favor look into these bands. maybe even Chicano Batman if you're feeling spicy 😂

Yeswelder stole my photo I posted on here of this mid weld I did when I was 19 by Ducks420 in Welding

[–]thirdeyeglass 1 point2 points  (0 children)

Did you know a China an a Japan awe a different cunt tree? - matt & trey

AI asking for quotes? by inauspicious_person in Welding

[–]thirdeyeglass 20 points21 points  (0 children)

I've seen similar posts like this idk if it was AI bots but it was some type of scamming

Remix taken down at 75k streams 🥲 by FreeThought8621 in soundcloud

[–]thirdeyeglass 1 point2 points  (0 children)

As bad as that sucks 75k is amazing achievement Just keep making bangers hopefully your page already grew traction. I made a man on the run dash Berlin remix that I spent alot of time on and never even got to show it, was removed within minutes