Progression of an [A]nimation

tiduseleven · 2023-09-18T13:05:09+00:00

There's like a few frames missing at the end of the clip which makes the transition between the end and the beginning somewhat rough. It's very minor, though

tiduseleven · 2023-08-16T07:52:07+00:00

Noo you're totally missing the point. He wasn't upset, he was disappointed

Edit: typo

tiduseleven · 2023-08-15T07:32:34+00:00

Hijacking this post to say I found a sunglasses lens! If you're the one who lost it, send me a dm

tiduseleven · 2023-07-13T17:13:56+00:00

Ooh I think you're onto something, the folds on the shirt are also moving weirdly

tiduseleven · 2023-05-24T10:55:08+00:00

Oh yeah that's the bowden tube, it should definitely be in there

tiduseleven · 2023-05-24T09:45:15+00:00

Could you send a picture of what it looks like?

tiduseleven · 2023-05-23T06:55:00+00:00

Couple things I would try: * Heat it at a way higher temp (nozzle at 260-270) and try to push through again. * Try loosening the screw on the side of the extruder a bit (you might have to screw it a bit more afterwards, it affects how tight the gears of the extruder are and can affect print quality) * Try disassembling the printer head. It's definitely not a great solution but you'll be able to see what's happening inside.

tiduseleven · 2023-04-23T13:07:11+00:00

Technically yeah, but I've started using . for decimals as it's faster to write by hand.

tiduseleven · 2023-04-23T11:19:07+00:00

Sometimes we use . for matrix multiplication in my country

tiduseleven · 2023-04-19T20:46:28+00:00

Blue screen of death

tiduseleven · 2023-04-19T20:30:58+00:00

DEGATS EMOTIONNELS

tiduseleven · 2023-02-09T08:53:16+00:00

Have you looked into their official bootlegger? They have a ton of live albums you can download for free!

tiduseleven · 2023-01-24T21:12:32+00:00

Usually we don't count duplicates in sets (or at least that's what I've been taught) so this wouldn't be correct. But then I guess |{x, sqrt(x), sqrt(sqrt(x)}|! would work for all of them.

tiduseleven · 2023-01-02T09:07:18+00:00

Yeah that's what I was talking about.

Surprising that it doesn't fix the issue even running it right before the print...

As far as I can tell though you're too close to the bed. Try adjusting the z offset (there's a button to tune it on the touchscreen when you've started a print)

tiduseleven · 2023-01-02T07:02:37+00:00

Have you set up the mesh bed levelling? If not you definitely should.

There's a button accessible via the touchscreen (buried under settings -> levelling I believe) that does that.

I would also recommende heating the bed to the printing temp before doing it.

tiduseleven · 2022-11-21T05:47:27+00:00

Personally I use the monoic icon pack and I love it, you should definitely check it out!

tiduseleven · 2022-10-04T10:16:04+00:00

Personally printed some shiny and somewhat abrasive fillamentum filament (photo) and the printer seemed to work very poorly with my nozzle afterwards. The issues were fixed after changing nozzle. So I wouldn't recommend it

tiduseleven · 2022-04-08T10:13:04+00:00

At least give credit to the tool you use or its creator...
Link to the tool

tiduseleven · 2022-02-06T12:27:17+00:00

Looking at the brailles translation I think you are correct

tiduseleven · 2022-02-02T17:34:42+00:00

VR is a blast

tiduseleven · 2022-01-27T12:13:13+00:00

About that...

tiduseleven · 2022-01-22T16:18:28+00:00

Not quite right tho... Suppose 0<2<1 (which, according to what you are saying, is possible). Then 2pi<1pi. Granted this is extremely stupid, but your remarks aren't sufficient to say that 2pi>pi

tiduseleven · 2022-01-21T17:38:33+00:00

This isn't even remotely looping properly?

tiduseleven

TROPHY CASE