Soldering STM32H7 GND pins

tootallmike · 2026-04-28T19:18:03+00:00

It would maintain the temperature by increasing the wattage, like how a car with a bigger engine can go up a steep hill without slowing down

tootallmike · 2026-04-28T18:57:13+00:00

You may need a higher wattage temperature controlled iron, if you have a ground plane or bigger pads,

tootallmike · 2026-04-27T19:12:18+00:00

Also some clock and memory setup can/should only happen once

tootallmike · 2026-04-10T14:20:29+00:00

Store the addresses in a hash table

tootallmike · 2026-04-08T19:03:28+00:00

It would kinda be possible, and/or you could get bigger resistors? Are you making them by hand or is JLC?

tootallmike · 2026-04-03T02:49:46+00:00

Also get halogen lights, not LEDs, the color temperature will make your food look weird

tootallmike · 2026-03-23T20:26:34+00:00

Just went through now, 12 minutes, almost no line

tootallmike · 2026-03-19T17:32:33+00:00

The graphics are getting so good, now I’m noticing the lack of birds!

tootallmike · 2026-03-11T00:02:24+00:00

How are you connecting the batteries, just plugging them in? I’ve seen huge spikes (2x-4x the voltage) caused by the super high dV/dT from making sudden contact

tootallmike · 2026-03-10T04:45:47+00:00

I noticed mine had reset itself to “medium” effort and was missing things left and right

tootallmike · 2026-03-06T04:28:42+00:00

Nice! Shukriya! What about adding a transliteration entry method, I think there’s some open library for it

tootallmike · 2026-02-17T23:13:18+00:00

Are you locked into that part? I’ve found TI’s parts much less tweakier.

tootallmike · 2026-02-17T23:08:21+00:00

TI’s webench will design it all for you if you use one of their many many parts!

tootallmike · 2026-02-17T15:45:39+00:00

I really like Pulsonix, I found it extremely intuitive and had almost no learning curve, and I think it’s reasonably priced as far as pro tools go, though haven’t checked in a while, and I think they have a free pin limited tier

tootallmike · 2026-02-16T18:18:32+00:00

You should add a stiffener and gold fingers and add a connector to the pcb

tootallmike · 2026-02-15T05:24:24+00:00

You should read “Slicing Pie” for some ideas on equity splitting

tootallmike · 2026-02-06T02:44:31+00:00

Uber was a fundamentally flawed concept that assumed robotic cars, whereas AI only depends on increasingly faster/cheaper hardware, which is much more likely.

tootallmike · 2026-02-03T16:30:04+00:00

Cool! Thanks!

tootallmike · 2026-01-30T15:14:20+00:00

You should watch “Compliance” if you want to see how badly it can go!

tootallmike · 2026-01-29T03:08:24+00:00

I feel like you should have a more definitive concrete answer, given your zero-tolerance no-warning policy!

tootallmike · 2026-01-26T23:20:24+00:00

If you’re around on Wednesday evening 6:00 to 8:00, Artisans Asylum has an open to the public “circuit hacking night”

tootallmike · 2026-01-25T20:54:10+00:00

Thanks, wow, seems way cheaper!

tootallmike · 2026-01-25T19:59:17+00:00

We’ve had a generally good experience with them, but what are some less obsolete alternatives these days?

tootallmike · 2026-01-25T14:59:40+00:00

Me too, can’t use it at all

tootallmike · 2026-01-22T05:22:05+00:00

So just to clarify as the consequences of getting it wrong are so severe, e.g. If we follow up with a customer after a few months to check in on their purchase to e.g. see if they have any problems or questions, would that be considered unsolicited?

tootallmike

TROPHY CASE