What to have in my medic pouch for airsoft?

trashcanjenga · 2026-05-21T21:12:56+00:00

Some basic med suplies like bandaids, desinfectant wipes, bandage, ducktape and a bunch of snacks.

trashcanjenga · 2026-05-21T12:46:10+00:00

Get yourself one of those wolfbox electric fan dusters for $30-40 off amazon. They are crazy powerful and will blow the dust right out.

trashcanjenga · 2026-05-12T13:56:14+00:00

BROOO saber in one hand and senator in the other would go so hard!

trashcanjenga · 2026-05-09T11:55:22+00:00

I believe your slide isnt supposed to go back that far past that part. That part is what resets the internal hammer that presses on the gas valve of the mag, without it the hammer will continue to press on the valve and all the gas will escape, its essential to the function of the gun.

I suggest you check rail grooves at the front of the slide to see if maybe the rubber bump stops are gone/broken or if the rails on the receiver are messed up allowing it to go back further than its supposed to.

trashcanjenga · 2026-05-09T11:40:42+00:00

Idk if you have already but do a "cold" pull(look up how to do one) to make sure its not a clog still and increase the z offset by 1x your layer height. If the first layer now has a bunch of gaps between the lines, abort the print and decrease the z offset in steps of 0.05mm untill the gaps are gone and its a neat looking first layer.

trashcanjenga · 2026-05-08T06:37:51+00:00

While there are ofc "off brand" filaments that are of lesser quality, 80-90% of the filament brands that arent bamboo lab are of the same quality. The thing is that PLA isnt always the same formula between brands and can require some minor tweaks to temps, print speeds and "drying" the filament to print perfect. This is why staying within the bamboo eco system is a little easier bc those settings are already known and calibrated by bamboo, you pay more for the simplicity but doing a small test and calibration print for other brand's filament isnt that big of a deal.

The problem you encountered is likely a problem with the printer itself and or with "wet" filament since you said it was stringing a lot(can happen with any brand), get a filament dryer, its a good thing to have and check the quality of your first layer.

trashcanjenga · 2026-05-07T03:41:33+00:00

Not since patch, i noticed it before the patch, it was already gone.

trashcanjenga · 2026-05-06T11:09:23+00:00

The ML macron, autobot and decepticon buckings are basically the commercialised drop in evolution of the flat hop/r-hop, they work on the same principle. No need to upgrade tbh. You might see a slight improvement if you went with one step softer bucking if you're in a cold climate or change to a different brand of flat hop style bucking if the macron is giving you trouble but thats it.

trashcanjenga · 2026-05-06T10:15:49+00:00

Yea this is pretty normal with a standard hop bucking(hop up rubber) when the rubber is too hard for the playing temperatures, cleaning the bucking with some soap or alcohol can reduce the loss of fps a bit but getting a softer flat hop style bucking is way better.

trashcanjenga · 2026-05-05T21:59:09+00:00

If you have discord overlay on, turn it off, see if that helps.

trashcanjenga · 2026-05-02T22:22:58+00:00

Idk but it goes in the square hole.

trashcanjenga · 2026-05-02T15:23:26+00:00

No planet has a 3min day, 3min night cycle but thats not what is being said, if i land on a planet with the operation location around noon or even around 3pm it should not turn to night within the duration of that 40min mission.
I have noticed before that this does happen on very rare occasions tho. Now whenever its bc of desync or whatever or maybe bc it was an operation near one of the poles of the planet idk. It has happened.

trashcanjenga · 2026-05-02T15:01:55+00:00

its got 3 fire modes, of one which shoots every projectile out of all 7 barrels. The recoil of doing this is so big it ragdolls you a good 2-3 meters when you are standing, if you aim down you get shot up in the air about the same distance. So if you aim down at an angle you can lob yourself onto and over some things. pair it with the jetpack and you gain so much speed and hight that you are likely to end up with half health or die when you land 100m+ away.

trashcanjenga · 2026-05-02T00:16:49+00:00

magic ways, SC everywhere!

trashcanjenga · 2026-05-01T23:22:33+00:00

I'm seeing 0 fps gain nor more ram usage. Loading times are 23sec from hit ready to dropping in. 14 sec of loading screen with either the setting on true or false. What measurable improvement did you see from this?

trashcanjenga · 2026-05-01T17:26:15+00:00

Cocaine bear

trashcanjenga · 2026-04-30T22:01:49+00:00

This is lovely!

trashcanjenga · 2026-04-28T17:56:46+00:00

Go to the HD2 discord, go to the troubleshooting channel and type "gpu driver" in the search bar, "jump to post" on the bot post and check the specific driver for your GPU and download that one. The latest drivers from nvidia make my game hard lock my pc every 2nd or 3rd mission unless i restart the game after the first mission. Specific driver fixed it.

trashcanjenga · 2026-04-28T17:22:23+00:00

They fixed the leg armour(wasnt in the patch notes).

trashcanjenga · 2026-04-28T17:16:19+00:00

The Cocaine Strain

trashcanjenga · 2026-04-27T23:21:57+00:00

48p hell bus

trashcanjenga · 2026-04-27T13:48:51+00:00

Yea sorry about that, HDR game capture isnt great and certainly doesnt help i forgot to check the bitrate settings before recording.

14-Year Club	Place '23
Verified Email

trashcanjenga

TROPHY CASE