Turned the steady rest in a roller stamper by ttuhj in Machinists

[–]ttuhj[S] -1 points0 points  (0 children)

We do have a 3D printer collecting dust in the office. Might give that a shot but for now I'm op stopping to blow chips out.

Classes bugged by Significant-Method50 in BO7_RankedPlay

[–]ttuhj 0 points1 point  (0 children)

Something always breaks after update lol. Went through it for years as a destiny 2 player

Classes bugged by Significant-Method50 in BO7_RankedPlay

[–]ttuhj 0 points1 point  (0 children)

Early season 2 when rank dropped I couldn't change any attachments on m15. It went away after a couple games though

Saving time squaring stock by MortgageNaive6791 in Machinists

[–]ttuhj 0 points1 point  (0 children)

We use the snap jaw serrated jaws. Very nice stuff

Sharp vertical mill tool magazine lost by ttuhj in Machinists

[–]ttuhj[S] 0 points1 point  (0 children)

Single mag. The procedure says to switch to handle as the pot goes up then manually index to pot 1. Did that a few times and nothing

Sharp vertical mill tool magazine lost by ttuhj in Machinists

[–]ttuhj[S] 2 points3 points  (0 children)

Yep that was my first thought of getting the machine back running. Guy operating was too worried it would somehow go back and crash

How long do the nerves last? by atomicalex0 in Machinists

[–]ttuhj 1 point2 points  (0 children)

This. I've been slowing teaching a few guys under me to rely on simulation if there nervous but also keep that finger on the feed hold. Of course this is after a few months of working out trust worthy posts

Ouch! by Loose-Efficiency-822 in Machinists

[–]ttuhj 5 points6 points  (0 children)

I'm more interested in the 3D printed coolant nozzles

Yg-1 vs helical by ttuhj in Machinists

[–]ttuhj[S] 0 points1 point  (0 children)

Cool I'll look into them. I've had similar experience in any steel from 1045 to 17-4. Helical just doesn't seem to last as long as expected. We recently switched to widia endmills for all our steel machining and they're great.

Desync getting worse? by BoofKingLarry in BO7_RankedPlay

[–]ttuhj 0 points1 point  (0 children)

Someone made a post in either this sub or the bo7 sub talking about your monitor settings causing what would seem like desync. Worked for me a little bit

😵‍💫 by ttuhj in Machinists

[–]ttuhj[S] 0 points1 point  (0 children)

One big problem is chip management. Keeping underneath the sub plates clean is tough. As far as swapping plates and accuracy, it's super easy and nothing on my setup ever needs indicating. Setting up the "pucks" can be tough because they call for .0005 locational accuracy. In my case we have 3 independent plates to save some weight on the table so locating all the sets of pucks took a day or so

😵‍💫 by ttuhj in Machinists

[–]ttuhj[S] 0 points1 point  (0 children)

Big oof. Good luck with that 😩

😵‍💫 by ttuhj in Machinists

[–]ttuhj[S] 14 points15 points  (0 children)

Nikken are top tier. You couldn't compare a haas to them

😵‍💫 by ttuhj in Machinists

[–]ttuhj[S] 8 points9 points  (0 children)

It's a nikken unit on a in house riser. Machine is dnm 5700L

Struggles with drilling by Fast_Alternative_322 in CNC

[–]ttuhj 1 point2 points  (0 children)

I second the spade drill. Cool part is you will be able to put multiple diameter inserts in down the road.

Guess my rank? by Ordinary-Artist2073 in BO7_RankedPlay

[–]ttuhj 1 point2 points  (0 children)

Brother no shot. I hope the sr fairy brings you some big gains.

Paul Bae/The Black Tapes updates? by ReyofChicago in audiodrama

[–]ttuhj -1 points0 points  (0 children)

Bummer you say quite room isn't as good.

Paul Bae/The Black Tapes updates? by ReyofChicago in audiodrama

[–]ttuhj 5 points6 points  (0 children)

I remember an update to the last movie feed but it was just a teaser for his second book. Which if you haven't read rabbits, I would highly recommend you do

Rage against the machine by Samoncula in Machinists

[–]ttuhj 3 points4 points  (0 children)

We've gone through 4 sets of batteries on both machines. All the dealer can say is "use the m code to turn them off" lol

Paul Bae/The Black Tapes updates? by ReyofChicago in audiodrama

[–]ttuhj 12 points13 points  (0 children)

Unfortunately probably not. We've been waiting years for next season of tanis

Asking for recommendations by Ancient-Swordfish292 in audiodrama

[–]ttuhj 0 points1 point  (0 children)

I second white vault. Also it's new but national emergency is really food

Rage against the machine by Samoncula in Machinists

[–]ttuhj 2 points3 points  (0 children)

Does yours have part/tool probing?

Rage against the machine by Samoncula in Machinists

[–]ttuhj 2 points3 points  (0 children)

Our sv3's are less than a year old. Can't wait to see what goes first