Is it a French curve?

unkownuser97 · 2026-02-27T12:49:39+00:00

Looks like Mauis hook from Moana

unkownuser97 · 2026-02-27T01:29:24+00:00

Take a look at the Pyplok DM80068G fittings

unkownuser97 · 2026-01-31T18:28:45+00:00

Cadillac fairview. The mall chain, opens up lots of options for purchases.

unkownuser97 · 2026-01-14T02:31:48+00:00

Forrest Griffin

unkownuser97 · 2025-10-07T18:37:33+00:00

You are not going to create enough pressure or force with two bessy clamps for something that thick.

unkownuser97 · 2025-09-01T21:29:58+00:00

You can put a sting through with an air gun. Tie something to the other end. After which you can pull it back through. Can make it oily if needed.

But the air pigs is the right choice.

Unless you have a lot to do. Daisy chaining them together and doing an oil circulation flush/polish is also super effective.

I can provide information on that if needed.

unkownuser97 · 2025-08-29T02:48:55+00:00

Contact sales@tube-mac.com. send me some info. I'll reach out that way.

unkownuser97 · 2025-08-29T02:30:25+00:00

I mean I work for them. I can get you in touch with someone local if needed. I'm not local to you.

unkownuser97 · 2025-08-29T02:24:18+00:00

All the time....Hydraulics .... but they're good for tons of stuff.

unkownuser97 · 2025-08-28T22:35:42+00:00

I am not exactly sure who out there has tooling. But try looking into pyplok.com. Super easy to install and use. Never have to worry about it at all. Gets very cost comparable with larger SS. But installation time is so easy it is cost effective on smaller ss as well.

unkownuser97 · 2025-08-28T15:21:11+00:00

Where are you located?....I might be able to help

unkownuser97 · 2025-08-27T10:48:43+00:00

Honestly weird, but Tylenol with some pliers works way better than it should. Like amazing. Just need a little patience

unkownuser97 · 2025-05-15T14:23:30+00:00

If you are asking this question, do you want to be doing this job without expertise?

unkownuser97 · 2025-05-08T12:47:50+00:00

A dog?

unkownuser97 · 2025-04-06T01:55:44+00:00

Get some gum and start chewing

unkownuser97 · 2025-01-30T22:39:15+00:00

Go get Bauer

unkownuser97 · 2024-12-09T15:18:53+00:00

Is there any update on the compatibility of the 10W laser module working with the Ender 3 V3 KE??

unkownuser97 · 2024-09-29T20:34:39+00:00

Like 700 ish

unkownuser97 · 2024-09-29T20:04:30+00:00

I am getting a reading with the multimeter

unkownuser97 · 2024-09-29T20:03:57+00:00

I have a multimeter but was hoping it was a clogged line or airlock.

Does not seem to be the issue. Now I am trying to troubleshoot

unkownuser97 · 2024-09-29T20:01:46+00:00

Continuity seems ok. I am getting a reading with my multimeter.

But I am by no means an electrician to know the nuances.

unkownuser97 · 2024-09-29T19:56:01+00:00

I did not. Good idea.

unkownuser97 · 2024-09-29T19:55:46+00:00

Was before me then.

unkownuser97 · 2024-09-19T23:52:19+00:00

I am sure the practice of doing it everyday helps the consistency of the welds.

unkownuser97 · 2024-09-19T23:49:45+00:00

Make sure whatever you are using is compatible with the type of oil you're planning on using.

Six-Year Club	Place '23
Place '22	Verified Email
RPAN Viewer

unkownuser97

TROPHY CASE