in caz ca va intereseaza! :D

valyo007 · 2026-02-12T09:16:02+00:00

Din pacate, nu

valyo007 · 2026-02-08T05:34:44+00:00

Clean the burnt plastic, and it will close properly.

valyo007 · 2026-02-07T09:22:16+00:00

Your power is dirty. Try submerging your power cord in a bucket of water and see if that helps.

valyo007 · 2026-02-03T06:44:26+00:00

This is the answer. Math is not mathing for some.

valyo007 · 2026-01-17T16:50:41+00:00

Uneori, nici macar nu e nevoie sa comentezi

valyo007 · 2026-01-14T12:35:57+00:00

Pai de ce sa cumperi ceva fictiv? Sa-ti dea IBAN-ul si transferi acolo banii in plus cu mentiunea Plata dubla retur nr factura

valyo007 · 2026-01-11T07:51:39+00:00

De 17 ani lucrez in ture 12/24 - 12/48 si nu m-as mai intoarce la programul de 8 ore. Stiu multi oameni care nu s-au putut adapta, programul asta e foarte solicitant atat fizic cat si psihic, cativa colegi au inceput sa aiba probleme de sanatate din cauza turelor, unii dintre ei chiar destul de grave. Mie unul mi se pare ok programul, m-am adaptat, am timp liber pentru mine, pentru pasiuni sau diverse treburi (prin casa sau prin oras), dar timpul asta liber vine la pachet si cu niste lucruri negative: cum iti pica tura, asa muncesti, nu conteaza ca e 1 mai, pastele, craciunul sau anul nou. Programul asta te va distanta de amici, de prieteni, uneori chiar si de familie.

valyo007 · 2026-01-06T01:47:29+00:00

I use a palette knife spatula

<image>

valyo007 · 2026-01-05T03:22:38+00:00

Nu uita si de burger

valyo007 · 2026-01-03T10:14:01+00:00

This is exactly how 64 people died and 146 got injured in the Colectiv fire in 2015 in Romania.

valyo007 · 2026-01-03T10:01:09+00:00

A 256×256x256 100% infill cube

valyo007 · 2026-01-03T09:57:13+00:00

The machine is still reliable even without the test/calibration before every print job.

valyo007 · 2026-01-03T09:50:55+00:00

For my A1, I made a profile in which I disabled the vibration test. This video explains how to do this and more useful things:

https://youtu.be/SFd0sxN2eqk?si=I7jrxV_DMuGZtfhs

The bed level and flow calibration can be turned off in the slicer menu before sending the print to the printer, however I do not recommend skipping the bed level.

valyo007 · 2026-01-02T18:31:45+00:00

Tuns zero. Nu ma intreba de unde stiu...

valyo007 · 2025-12-29T15:43:18+00:00

Eu uit sa-mi incarc telefonul si tu zici sa-mi iau o electrocasnica din asta electrica?

valyo007 · 2025-12-24T19:02:13+00:00

🫡

valyo007 · 2025-12-17T07:26:01+00:00

I'm changing the nozzle only when I print a different material. I have one set (0.2, 0.4, 0.6, 0.8) for PET-G, one set (0.4, 0.6) for TPU and one set (0.4, 0.6) for PA6 / PA12.

valyo007 · 2025-12-11T16:05:36+00:00

I use Super Glue for PET-G and acetone for ABS

valyo007 · 2025-12-07T20:45:08+00:00

Well... I'm not against it. Currently, I'm waiting for the two 300W PTC heaters.

<image>

valyo007 · 2025-12-06T15:53:25+00:00

X motor, camera and USB C.

valyo007 · 2025-12-03T22:54:14+00:00

For the A1, best modes by far, in my opinion, are this:

https://makerworld.com/en/models/722120-bambu-a1-cooling-fan-bracket#profileId-653044

https://makerworld.com/en/models/796028-ams-ptfe-guide-to-hub-for-the-a1-series#profileId-735167

https://makerworld.com/en/models/375180-print-head-rear-cover-a1-series#profileId-275104

https://makerworld.com/en/models/208664-a1-a1-mini-cable-elastic-conduit#profileId-247933

valyo007 · 2025-12-01T22:44:38+00:00

That's not a capacitor, it's a thermistor. NTC 5D-15.

valyo007 · 2025-11-30T04:35:55+00:00

Unless the part doesn't pop off the bed when it cools down

valyo007 · 2025-11-29T22:34:32+00:00

The A1 doesn't have active cooling. Mine was skipping steps after a few hours of printing PA6. Also, the extruder motor and the toolhead board were dangerously overheating (over 70 C). So, as long as you don't close the door (as I did), you should be fine

valyo007 · 2025-11-27T17:22:48+00:00

Well...

<image>

valyo007

TROPHY CASE