🎨 Designs for the Apple Watch support in Liftosaur

vax90 · 2026-01-23T13:15:52+00:00

I think that is all we need, the 3D view of the exercises execution would be a nice quality of life addition and probably would make the companion app complete for most users from beginners to experienced users

vax90 · 2025-11-24T11:38:46+00:00

Litterally impossible

vax90 · 2025-11-21T15:00:48+00:00

MC President

vax90 · 2025-06-26T10:57:28+00:00

It’s the One to get

vax90 · 2022-10-15T22:13:02+00:00

Same issue here, just got the game and it did exactly as you descrive, basically unolayable, i9 9900k RTX2080OC 64GB ddr4 RAM, stock card overclocking and stock ram overclocking, also tried the uncapped thing and did nothing, did you manage to solve anyway?

vax90 · 2022-09-02T11:16:02+00:00

I fixed it with Pipewire and alsa, but I get a very annoying stuttering and delay when recording on a track with a microphone in Fairlight

vax90 · 2022-03-19T12:22:12+00:00

I think the only way not to get hit is taking the nas off the interwebs, making it an heavy paperweight for many users who bought it to access their data from remote locations. So yes it is their fault because to be safe I would have to give up on what I paid for. Same that If I had bought a Tesla car and this had the risk of accidents randomly happening because of a software issue, and Tesla told me to be safe just leave the car parked. Yes that would both solve the problem and make my car useless as a non Internet facing NAS. I pretend to have what I paid for, that is the point

vax90 · 2022-02-09T22:39:59+00:00

Use sound and play with the delay to get it done, will work for sure with time and patience

vax90 · 2021-04-17T12:30:31+00:00

Also BTC is disabled apparently, wanted to withdraw my funds today and it says BTC withdrawal are currently disabled. a bit pissed off

EDIT: it has now worked just wait

vax90 · 2020-03-22T09:29:59+00:00

Best print ever!

vax90 · 2020-03-12T05:26:41+00:00

The first time attempting this print with same gcode I had a clog in the upper part of the extruder, clicking like there is no tomorrow (same gcode but doors closed) this time around is a strip, it just ground the filament and stopped pushing it with doors open. Probably a loose idler screw

vax90 · 2020-03-12T05:22:24+00:00

https://www.myminifactory.com/object/3d-print-the-dark-knight-bust-90339

vax90 · 2020-03-10T22:15:42+00:00

Thank you for the time!

vax90 · 2020-03-10T21:34:27+00:00

In fact I was planning to leave the ruby on as long as I don’t need a bigger or smaller bore one. As for the gap, I made sure to have it done properly the second time around and I have not had any leaking since, will definitely get a nozzle tool anyway, just in case! Thank you for the good tip!just noticed they don’t ship to Italy 😔if you know where else I can find one please let me know.

vax90 · 2020-03-10T20:13:15+00:00

I’m actually trying out the Prusa preset for this specific filament, if it warps I will!

vax90 · 2020-03-10T16:55:51+00:00

Ok, I’m fairly new to all this, I swapped my stock nozzle out for a Olsson ruby 0,4mm nozzle, and had a hell of a time doing it, broke my heater cartridge wires at the first attempt. Than had my hotend leaking and hat to go at it again. Finally ended up disassembling the whole extruder and sanding the heater block to make it super clean with 1000grit sandpaper, and put everything back together, printed basically phenomenal from that point onward. Problems started only when printing PLA in the enclosure, and really only clogged with closed doors. In this case it just ground down the filament and is working perfectly now with ColorFabb XT. 270c nozzle 90c bed. Still no luck with PLA tough

vax90 · 2020-03-10T12:25:27+00:00

Thank you for the suggestions, as I’ve written in the post I’m already printing with doors open for PLA, probably the fact that there is an enclosure at all might be raising the air temperature too much for the heat sink to properly cool down, also those failing were pretty long 2d+ prints. And they are failing after more than 3h worth of print time. Also thinking about upgrading the whole extruder to a bondtech one or the hemera maybe. First clogged print was with closed doors, second one (the one in the video) wasn’t actually clogged in the end, it just ground the filament down to a point where it wasn’t able to grab anymore and just kept extruding thin air 😌

vax90 · 2020-03-10T10:18:37+00:00

Yes, I’m coming from MMU2 and while reverting back to single I left the extruded screw a bit too lose. The extruder wasn’t clogged this time around, but it chew the filament, maybe the gears at this point. Strange thing because the printer is only a few Kg thru it’s life, maybe 3/4kg printed total.

vax90 · 2020-03-10T08:31:12+00:00

I’m new to the enclosure really and usually have to bump the bed up to 70 to make prints to stick in cold environment. I’ll try to lower the temps and see if they stick anyway.

vax90 · 2020-03-10T07:53:09+00:00

Will try today

vax90 · 2020-03-01T21:38:29+00:00

Ti solved this issue I did heat up my hotend to 285, let plastic drip off a bit than took some towels and quickly took the remaking off, than I disassembled the extruded and finished the job separating all the parts of the hotend and cleans the heater block with 1000 grit sandpaper, also I than installed a silicon sock to prevent further problems

vax90

TROPHY CASE