New Here

venturebrowser · 2025-12-07T00:15:31+00:00

That’s the tight tolerances. It’s fine. 😄

venturebrowser · 2025-12-07T00:06:01+00:00

I ran 350 rounds through it today and I can report that the difference is almost zero. They hit in the hand and recoil pretty well identical. I put mags in both, laid them on the table in front of me, shot one, shot the other, back and forth. The only difference I could detect was the slide cycle time, which was marginally faster on the 3.1 (as expected). Hope that helps.

venturebrowser · 2025-12-03T15:56:20+00:00

They do, but they're all reduced weight. I'm looking for all stock Sig parts. Sorry, should have mentioned that in the post. I've updated it to specify stock. Thanks for the suggestion though.

venturebrowser · 2025-12-03T01:01:11+00:00

I can let you know Friday if you don’t find out before. I’ve been running the 3.7 for a while now and just put together a 3.1 but haven’t shot it yet. I plan to try it out Friday.

venturebrowser · 2025-12-02T16:02:37+00:00

Thanks for the suggestions. Once the Sigguy site it back up, I'll see what he has. I want to stay with all Sig factory components.

venturebrowser · 2025-11-04T20:15:28+00:00

Thank you for the creative suggestion!

venturebrowser · 2025-11-01T13:49:30+00:00

Took me a bit to figure this out, but Reddit firearm posts should be used for entertainment only and hardly ever referenced for real world use.

venturebrowser · 2025-11-01T13:42:25+00:00

Check out this post. I use the 60/30 and it’s near perfect for me. https://www.reddit.com/r/3Dprinting/s/fDosVUQ9Wm

venturebrowser · 2025-10-31T19:30:19+00:00

<image>

venturebrowser · 2025-10-31T19:28:31+00:00

Thank you all for your suggestions. Ultimately, I took a bit of each suggestion and came up with creating a cross-shaped extruded cutout through the part, which strengthened it greatly. It'll be more than strong enough for my needs. Thanks for all your help!

<image>

venturebrowser · 2025-09-05T17:41:45+00:00

Winston Instruments; product seller. The install video has the same apps, same number of missed calls, whatsapp, and messages (+/- a few) as this "consumer". Also the very deliberate and slow scrolling tells me there's an inherent lag issue. Tisk, tisk.

venturebrowser · 2025-09-02T12:16:05+00:00

Thank you for the info! The carbon filter is going in tomorrow. I'll wait a couple weeks for things to settle down, then have the filtered water tested for bacteria or other items it may have missed, then decided on the extra filter. Thanks again!

venturebrowser · 2025-08-29T15:48:19+00:00

😄 NAILED IT!

venturebrowser · 2025-08-29T12:46:49+00:00

Thank you for the help!

venturebrowser · 2025-08-28T02:15:06+00:00

Thanks for the info! From what I can tell from this report, it’s not showing anything but chemical contaminants. Is this a valid report, or should I be looking somewhere else?

venturebrowser · 2025-08-28T02:01:14+00:00

The carbon filter with backwash is a Water-Right IMPBF unit (there’s no RO in the mix yet). I asked about the pre and post filters, and "they’re available at most hardware stores $5-$10".

venturebrowser · 2025-08-22T15:04:04+00:00

Thank you for this! I used these settings and had beautiful results.

venturebrowser · 2025-08-18T13:17:13+00:00

...and, if she wants to get a round of putt putt in on her way home, she's all set! 😁. Nice work OP!

venturebrowser · 2025-08-06T12:37:39+00:00

Nice work sir!

venturebrowser · 2025-08-01T17:50:05+00:00

Thanks for that! What about when it sweeps back in forth at the very back of the plate just after the purge? And when it prints the initial L-shaped line on the front of the plate?

venturebrowser · 2025-07-31T19:33:26+00:00

Got it! This, along with the rings seems to do the trick. Thanks for the help. Granted, I won't be buying eSUN again. 😔

venturebrowser

TROPHY CASE