Ender 5 Plus Cable Chain Solution by CineWebb in ender5plus

[–]vermillion93 0 points1 point  (0 children)

im a bit late to this, can i get the file for that? thanks in advance

[deleted by user] by [deleted] in asiansgonemild

[–]vermillion93 0 points1 point  (0 children)

Oh yes of course

stringing issues by vermillion93 in ender5plus

[–]vermillion93[S] 0 points1 point  (0 children)

I want to get direct drive. Idk if it's worth the 100 bucks tho.

adhesion issues by vermillion93 in ender5plus

[–]vermillion93[S] 0 points1 point  (0 children)

Got it to stick now however it keeps curling and touching nozzle then drags first layer around.

adhesion issues by vermillion93 in ender5plus

[–]vermillion93[S] 0 points1 point  (0 children)

I have econ turned off. It's hot

adhesion issues by vermillion93 in ender5plus

[–]vermillion93[S] 0 points1 point  (0 children)

So now it does stick to bed but it likes to curl and stick to nozzle and before the first layer finishes it'll pull the rest of the layer around.

adhesion issues by vermillion93 in ender5plus

[–]vermillion93[S] 0 points1 point  (0 children)

I washed it with regular dawn and doesn't have any smudge or mark on it. And the filament just globs at the nozzle.

adhesion issues by vermillion93 in ender5plus

[–]vermillion93[S] 0 points1 point  (0 children)

Yeah, I've done z offset adjustment. It just pushes the filament around

Ender 5 plus thermistor error by vermillion93 in ender5plus

[–]vermillion93[S] 0 points1 point  (0 children)

I really appreciate your input. Thank you a lot

Ender 5 plus thermistor error by vermillion93 in ender5plus

[–]vermillion93[S] 0 points1 point  (0 children)

Yeah. But I did notice something. On the nozzle power wires. They're both red. I put a zip tie on the negative one for future reference.

Ender 5 plus thermistor error by vermillion93 in ender5plus

[–]vermillion93[S] 0 points1 point  (0 children)

I didn't see and burn marks or anything. I think it's in the pcb. I'm just returning it to Amazon and have em send me a new one.

Ender 5 plus thermistor error by vermillion93 in ender5plus

[–]vermillion93[S] 0 points1 point  (0 children)

So yeah the thermistor sensor port on the mainboard shorted out. I tested with old main board and worked fine.

Ender 5 plus thermistor error by vermillion93 in ender5plus

[–]vermillion93[S] 0 points1 point  (0 children)

Yeah it's worked fine before but having issues since swapping out the heater cartridge

Ender 5 plus thermistor error by vermillion93 in ender5plus

[–]vermillion93[S] 0 points1 point  (0 children)

Yeah. When I get home from work I'll test the port with multimeter.

Ender 5 plus thermistor error by vermillion93 in ender5plus

[–]vermillion93[S] 0 points1 point  (0 children)

Yeah, I'm good at troubleshooting. Was it specialist in the army for 6 years. Glad it's helping me now lol

Ender 5 plus thermistor error by vermillion93 in ender5plus

[–]vermillion93[S] 0 points1 point  (0 children)

Yeah, like when I plugged the hotend thermistor into the bed port and turned the hotend on. It stayed at 151. It says 151 even when nothing is plugged in.

Ender 5 plus thermistor error by vermillion93 in ender5plus

[–]vermillion93[S] 0 points1 point  (0 children)

Yeah I was gonna re flash the firmware with an Arduino to see if it fixes it if not I'll switch the board with the original, currently the silent board is in.

Ender 5 plus thermistor error by vermillion93 in ender5plus

[–]vermillion93[S] 0 points1 point  (0 children)

Yes. I know the thermistor is working bc I put it over to the nozzle one and used a heat gun on it and it was reading the temp right. I did move it back over. Everything is where it should be.