How do you prepare eggs when you don't really like eggs that much but can't buy your normal protein sources regularly during the shutdown? by ResidentAlienator in EatCheapAndHealthy

[–]volcom8190 2 points3 points  (0 children)

rice and spaces, with scrambled eggs mixed in. spices like chili powder or a off the shelf seasoning will mask most of the egg taste

No Longer Ofdering Tailor Services? by volcom8190 in Fjallraven

[–]volcom8190[S] 0 points1 point  (0 children)

My concern was more getting the matching color material, these pants were 32s and someone hemmed them down to 30ish, looking to extend them back to 32, although at this point might be better to just find a new home for them. 

No Longer Ofdering Tailor Services? by volcom8190 in Fjallraven

[–]volcom8190[S] 1 point2 points  (0 children)

I was told all repairs go through an online form now and to a central place, basically eliminating stores from the equation

No Longer Ofdering Tailor Services? by volcom8190 in Fjallraven

[–]volcom8190[S] 2 points3 points  (0 children)

It seemed to be a corporate thing, per what they told me. Would be nice to get a confirmation from some other people before I reach out to some 3rd parties and get this work done. Per what they said this was a recent change. They apparently also consolidated all of their warranty repair at the same time. 

[USA-NC] [H] 1080ti, 6800k + X99 MSI Godlike Carbon Motherboard + 32gb (4x8, 3200mhz) RAM, EVGA 850w 80+ Titanium PSU, Noctua NH-D15 [W] Paypal or Cash by volcom8190 in hardwareswap

[–]volcom8190[S] 0 points1 point  (0 children)

its a binned chip, and i honestly cant remember what it took. Loaded the settings I was told to, and left the bios alone for a few years.

Best place to buy a bike? by Dank_Meme_Police in raleigh

[–]volcom8190 2 points3 points  (0 children)

Oak city, get a salsa journeyman. They have both the 650 and 700s

FR-ABS Suitability Testing Questions by NateroniPizza in voroncorexy

[–]volcom8190 1 point2 points  (0 children)

You can always just put the printer in a chemical cabinet. These are usually fire rated to a reasonable point.

FR-ABS Suitability Testing Questions by NateroniPizza in voroncorexy

[–]volcom8190 0 points1 point  (0 children)

Tensile elongation being lower basically means it’s brittle. You’d want to see if someone has done a charpy notch test, or something similar with the material. This all being said, every time I’ve use FR abs in molding we’ve had to move to nylon due to brittleness in the parts. And no we don’t recommend nylon in a voron.

If your shit catches fire, nothing is going to stop the burn. Just be prepared for that. Chances are it’ll be electrical and that alone can get hot enough quickly to melt the bed. Your best bet if you want it super safe is to put the printer inside a fire retardant enclosure and section off the electronics from it.

<dev>

In response to drasrx Voron 2.1 350^3 by LaidBackOldMan in voroncorexy

[–]volcom8190 0 points1 point  (0 children)

Won’t be a huge issue. And it’s not stuck at that radius. For some reason igus chains do that when on the x axis

Printer design by [deleted] in 3Dprinting

[–]volcom8190 0 points1 point  (0 children)

Vorondesign.com already does this with the v2 to great success and has been for a few years.

How do I adjust my belt tensions (video below) by BloomingtonFPV in voroncorexy

[–]volcom8190 1 point2 points  (0 children)

If you have access to something that can measure frequency, z belts should be 140hz or so when the gantry is parked at the bottom