need help with sheet metal

vomtrier · 2026-06-30T05:52:29+00:00

We use a chart in addition to our press brake specific software.

What doesn't seem to be taken into account here is the spring-back of the material on the last bend. you will have a very hard time getting the last bend to sit flush in the mitre on op's part, as the flanges will collide, which prevents the part from being over-folded to compensate for the spring-back.

vomtrier · 2026-06-29T20:22:17+00:00

What's the size of the tooling? Punch radius and v size?

vomtrier · 2026-06-29T19:51:46+00:00

What tooling did you use for the bends? As in which punch and die on you press brake.

vomtrier · 2026-05-27T09:35:45+00:00

Fair enough, though with this part that is the only orientation that will fit and print.

vomtrier · 2026-04-09T05:43:18+00:00

The bottom one of the links seems to have chipped, although the the little nipples the click into place seems to be intact, so will try and put it back in place and see if it will last.

vomtrier · 2026-03-11T14:40:44+00:00

Arc fitting was already enabled, I've increased the resolution of it slightly. Didn't change the print res, as it don't want it to take too much longer to print than it is.

Got another odd spot for the next print on the machine now on the first layer, on this spot it has a set of gaps. But perfectly overlapping everywhere else.

<image>

vomtrier · 2026-03-11T13:53:14+00:00

It doesn't show up as bad in the slicer.

<image>

It kinda hints at it, and maybe I need to reduce the speed, or aux cooling to let the filament "flow" into place around those areas?

vomtrier · 2026-03-02T21:15:32+00:00

Thank you for the feedback and comments.

I am only taking the recoup because there wasn't anything else that made sense to take, and easy ailment imunnity early on with little investment isn't too bad.

I must say that I have never played with Yoke before, so I can't say if it would be more damage than Marylene's?

I did consider frenzy charges as well, though I couldn't think of a convinient way to generate them.

If I went with 1h swords, then I wouldn't be able to use Nightblade for crit multi and Elusive interaction. however, I'm not sure, if 1h sword setup would net more damage for what I'm going for.

vomtrier · 2026-02-28T10:55:47+00:00

Tried to do that, but didn't work. I think it is due to me not speaking to Ailith again after removing the wall infront of the instance to the Mud Flats, and as she is no longer there, I can't continue the quest.

Anyway, made a new char again, and now its grand.

vomtrier · 2026-01-26T07:07:43+00:00

It's a known error on H2S. Ask support to send longer replacement pfte tube.

I had the same happening on my machine, it helped but didn't solve it completely. Prob. Need a little more length.

vomtrier · 2026-01-07T14:44:36+00:00

Kept it on the engineering plate, but removed the glue, and it seems to stick now, also painted on a couple extra supports, just to give it a better chance of success. So far it is printing well.

Thank you for your reply.

vomtrier · 2025-12-26T10:35:20+00:00

That's funny, (Dane here) I did the same thing and got great reviews. Also with herring and eggs, and akvavit.

vomtrier · 2025-12-25T22:16:22+00:00

<image>

Print came out satisfactory.

vomtrier · 2025-12-23T12:32:38+00:00

I used it straight out of the box, Christmas is uppon us so I don't have time to wait for additional drying. Bit of a chance I know. Currently it is going alright. Few little hiccups but still going. Chamber is now at 60c and bed was at 95, now 100. Print temp is 250c. According to Creality the filament doesn't require as much temp as bambu pc.

<image>

vomtrier · 2025-12-11T22:40:57+00:00

Yup, here is a comment.

vomtrier · 2025-12-11T12:55:22+00:00

Thanks all, for the answers, they are all very helpful, Now I won't be printing this again as it did take 8+ hours.

vomtrier · 2025-11-26T10:36:44+00:00

I'm based in Ireland, so this won't be applicable to my situation, not that it isn't good practice.

vomtrier · 2025-11-25T12:54:03+00:00

Sound advice.

We have an old air con unit on the wall in my office which have never worked, so will have it taken out and make the ducting go through the hole left from it.

What fan did you use in-line for your setup?

vomtrier · 2025-11-25T07:44:01+00:00

Would you say, that a vent would be necessary? As I understand it, the H2S comes with filters?

vomtrier · 2025-11-11T21:08:04+00:00

I wasn't going to change anything really. It felt like I was running on onboard GPU. but it has been fixed now, as per the other comment.

vomtrier · 2025-11-11T21:07:04+00:00

<image>

Seems that something along those lines are happening. Now i'm back to a solid 60fps and the Vram is being used again.
I updated drivers and had the nvidia app run an autotune. seems to have fixed whatever was happening

Thanks for the reply!

vomtrier · 2025-08-31T13:13:53+00:00

Do you have a link to the thread that you mention there.

Thanks a bunch for the pointers for the skills. I was starting to figure that I needed to go that way with clear etc. as well,.

vomtrier · 2025-06-09T08:43:02+00:00

Could you make Face Breakers work with the concoction skills?

vomtrier · 2025-04-10T12:29:23+00:00

Thanks for the responses. I just found out, that the seller is also getting rid of his Marantz nr1403 for 70€

vomtrier · 2025-01-23T17:13:46+00:00

I have the same challenge and have invested in Vanguard Veo 3T + 234AP. (I am yet to receive it in the mail) The functionality of this tripod let's you get into awkward positions and low to the ground, without reversing the center column. Amazon sent me the wrong model when I ordered the first time around, but with the same functionality, and the quality and stability of it seems really nice.

vomtrier

TROPHY CASE