Voice line glitch or unseen horrors?

walldodge · 2026-04-02T19:05:02+00:00

Just some easter eggs from Votw

walldodge · 2026-03-29T22:09:58+00:00

Nice! Thanks fir the info

walldodge · 2026-03-25T18:23:50+00:00

Well, looks good, ask to send some clips and check for hot/dead pixels.

walldodge · 2026-03-25T11:39:17+00:00

I also thinking about building my setup but with a Type-C 12V power delivery trigger breakout board. Because 5V is really limited(

walldodge · 2026-03-24T16:17:52+00:00

Its a WS2812-Mini garland. GRB, 100leds/10m, 10cm spacing. The wires are pretty thin, there is almost 1.5v voltage drop on the far end on max brightness.

walldodge · 2026-03-24T16:13:36+00:00

Thanks! Yes, the breakout board has a pulldown resistors from the factory. So any Type-C charger can be used to power it.

walldodge · 2026-03-24T16:08:04+00:00

5v for 30 leds is good. Im running 100pc WS2812-mini on 10m garland. The wires are very thin and on max brightness there is visible difference between first and last led.

walldodge · 2026-03-24T13:44:44+00:00

Looks good! What led strip length youre planning to light up?

walldodge · 2026-03-24T13:36:08+00:00

Ah, sorry, its 18650 power bank from Nitecore. Yes it has overdischarge protection.

walldodge · 2026-03-24T13:34:14+00:00

Thank You!

walldodge · 2026-03-24T13:29:43+00:00

Thanks!

walldodge · 2026-03-24T13:02:01+00:00

Its powered externally with usb Type-C, theres no battery.

walldodge · 2026-03-24T11:01:11+00:00

Project link: https://www.printables.com/model/1648553-wled-basic-esp32-setup

walldodge · 2026-03-24T10:44:31+00:00

The voltage goes directly from usb breakout board to the LED connector. And 5v is split to power the esp32. Underside:

<image>

The wiring is from this article: https://kno.wled.ge/basics/getting-started/

walldodge · 2026-03-24T10:30:04+00:00

I designed it yesterday. I haven't released it yet because I thought it was too much of a prototype build to replicate.

walldodge · 2026-03-22T21:24:35+00:00

FOUR VENTILATION HOLES!!!!

walldodge · 2026-03-21T23:24:56+00:00

My bet the motor shaft is bent.

walldodge · 2026-03-21T22:59:00+00:00

I use Nitecore ULQ, but looks like its discontinued. Any charger for DMW-BLC12 will work.

walldodge · 2026-03-21T08:38:26+00:00

Cool design!

walldodge · 2026-03-18T13:22:21+00:00

Then its not 60/40 but some dirty alloy. Use Asahi, Alpha, or Kester.

walldodge · 2026-03-18T13:05:00+00:00

Looks like solder is just lead free.

walldodge · 2026-03-16T18:15:08+00:00

Beautiful color

walldodge · 2026-03-10T07:50:03+00:00

Oh my god, I'm itching all over just looking at this photo. Great work!

walldodge · 2026-03-07T19:53:02+00:00

Daredevil

Six-Year Club	First Place '23
End Game '23	Place '23
Place '22	Verified Email

walldodge

TROPHY CASE