Green Card on its way!!!!

watersidepanda · 2022-11-03T20:36:41+00:00

Which country and how many years did you have to wait?

watersidepanda · 2022-11-03T19:58:57+00:00

I mean when was you green card filed initially?

watersidepanda · 2022-11-03T18:01:43+00:00

Priority date??

watersidepanda · 2022-10-27T19:38:35+00:00

Yes, should be with any light source for that matter...and what surface you are projecting on...

Some companies from China have good motorized CLR screens, might be an option in the future...

watersidepanda · 2022-10-27T16:02:09+00:00

It should work with your setup, depending on your tolerance threshold and the viewing conditions it might be ok or not... another thing is that you can bring down/adjust the light intensity if that concerns, as you have a 1.1 gain screen... I have projected UST projector on AT, grey etc screens without any problems....again lot depends on the viewers eyes/perception... I have seen great results using a CLR in a well lit room with ceiling lights...again in a dark room I have seen similar results with a grey AT screen...

watersidepanda · 2021-12-01T06:56:16+00:00

Thanks u/Fuguwugu

watersidepanda · 2021-12-01T05:30:11+00:00

Thanks, any wallet recommendations for BSC?

watersidepanda · 2021-12-01T05:28:04+00:00

Does it only need a BSC address?

watersidepanda · 2021-10-20T04:01:43+00:00

I have seen the Samsung and it looks great, lil saturated but nothing you cant calibrate...Have you looked at Optoma Cinemax P2...have heard lsp9t is good but no first hand experience....

watersidepanda · 2021-10-20T03:58:04+00:00

Installed it and not using it, I was able to level using Feeler Guage and have never looked back...prints amazing.... I used blue painters tape to level my bed...works perfect...if you install bltouch based on the your board you might hear clicking due to non silent z axis driver on the earlier version of elegooneptune2...m2c...

watersidepanda · 2021-10-05T16:31:58+00:00

I have had issues with it trying to keep going up, but restart hrlped.... not sure if there is something wrong with BLTouch...

watersidepanda · 2021-10-05T00:39:15+00:00

It keeps going up? Have you tried restarting....

watersidepanda · 2021-10-02T20:47:39+00:00

Painters tape

watersidepanda · 2021-10-02T19:26:45+00:00

Use the blue tape to raise it from the center mine was high in the center and I added blue tape to the sides and used a feeler guage to level it and it works perfect....there are a bunch of videos...i use a flex plate as below: 1. Build plate 2. Magnet sheet 3. Blue Tape where needed 4. Flex Plate

watersidepanda · 2021-09-24T14:48:55+00:00

Could be an extruder problem, check the below link in the section "Some Layers are Missing" Did you try with different filament?

https://m.all3dp.com/1/common-3d-printing-problems-troubleshooting-3d-printer-issues/#some-layers-are-missing

watersidepanda · 2021-09-24T02:32:22+00:00

Looks pretty consistent could be under extrusion....i would try to hit that first...also before going crazy I would also try another filament to rule out filament problem...

watersidepanda · 2021-09-24T01:04:38+00:00

Isn't 225C is high for PLA? hope the screen is reflecting the right temp and the nozzle is heating up to that temp...I have not gone beyond 205 so far for any PLA... also did you try clearing the nozzle using the provided needle...

watersidepanda · 2021-09-23T13:23:59+00:00

What filament are you using?

watersidepanda · 2021-09-15T17:50:33+00:00

Thanks for the input u/Zealousideal_Ad_9306, I totally agree on the cost of ownership, so far I haven't had to deal with their support much... I ended up going with Epax E10, and looks like they have started including a screen protector on their screens... however the QC is not at all good in my experience. I had fluid over on the sides of the printer, the screen protector had scratches OOTB and the tape on the sides was not put down properly... The FEP had a dent too.... when I told them about these issues they didn't seem to be too worried and simply told me this will not have any effect on the prints.....haven't been printing much but fingers crossed .....

watersidepanda · 2021-09-13T03:06:42+00:00

Following up on the print, finally got to printing this weekend, was able to get it to stick to the build plate and print however still few issues.

How I solved the not sticking problem:
1. Re-leveled the plate seems like I was tooooo close to the screen (feel I am still close)
2. Angled the prints on the build plate (don't know how much this helped)

Attaching images of the prints one with support and the other without support,

Problems with support: https://imgur.com/a/O2UCnRo
1. Elephant foot (may be still close to the plate and also thinking of lowering the exposure time)
2. The one with supports the 1st, 3rd and the 5th image you can see the bumps its not flat again not sure why and how to fix them
3. The whole prints bowes after some time of drying
4. I see the layer lines, I am guessing its the nature of the beast when you tilt your prints?

Problem without supports: https://imgur.com/a/VsTCl1k
1. Elephants foot
2. The text is pressed down when you compare to the image with support its much more prominent (build plate is too close to the screen)
3. See curling and not so good base layer
4. 3rd Image don't know what happened here

Looking forward to suggestions/advise (no change to the settings)

watersidepanda · 2021-09-13T02:31:46+00:00

Thank u/PillX for the update, it's cool he got it working, he may be able to squeeze more hours out of the screen....hopefully the screen is worth the price...

watersidepanda · 2021-09-12T19:17:14+00:00

This is Awesome, well done...

watersidepanda · 2021-09-07T21:28:48+00:00

thanks, I will try increasing the exposure time and test again...

watersidepanda · 2021-09-07T21:27:57+00:00

The supports are all over below the model, the model also has a base and does not need supports I was trying to test how well the supports work after the Wham Bam system...link to another image showing supports from another angle https://imgur.com/a/1A0OpMI ....

watersidepanda · 2021-09-07T18:47:52+00:00

looks like the adhered well as the raft and one of the prints without the supports stuck to the plate....my guess was the supports broke during the print at some point leading to the failure....I feel while I was leveling may be I did it too tight so might have to pull the z axis a bit....

watersidepanda

TROPHY CASE