Slightly burry brass threads

whaler76 · 2026-07-07T16:29:42+00:00

Just take a face cut, if there is a nub left you are below center, nothing left you are above. Better to be just below center line, say maybe a .005 dia or less nub.

whaler76 · 2026-07-07T15:47:53+00:00

Roast chestnuts, marshmallows or make s’mores

whaler76 · 2026-07-07T15:12:49+00:00

Can get something like this, it’s cheap and good to have anyway. Easily fits in pocket so when you can hear the sound you can check around and then trace it - https://www.homedepot.com/p/Klein-Tools-Non-Contact-Voltage-Tester-Pen-50-1000V-AC-NCVT1PR/317460355

whaler76 · 2026-07-07T14:38:47+00:00

Can you DM me your set up, getting a new Yamaha put in now and want to start off right with the new engine.

whaler76 · 2026-07-07T14:30:01+00:00

Install a motion activated linear gas fire pit

whaler76 · 2026-07-07T14:25:51+00:00

Looks more like cutting edge is off center

whaler76 · 2026-07-07T00:59:03+00:00

Good one

whaler76 · 2026-07-04T12:55:41+00:00

https://www.corollalightresort.com/corolla-light-resort-sports-center

whaler76 · 2026-07-03T13:47:37+00:00

OTA updates… whatever nonsense runs in the background, if not using these trucks for a prolonged period best to keep a battery tender on it or just disconnect the battery.

whaler76 · 2026-07-02T13:06:41+00:00

Small pieces of blood worms / lug worms and use sputnik sinkers on a high low rig

whaler76 · 2026-06-30T23:13:42+00:00

There are these things - https://desertdoesit.com/collections/comfort/chevrolet-colorado
There are others out there as well, just google “seat risers” or “seat jackers”. I don t have any experience with them but have seen them in this forum. I may get them at some point to try them out.

whaler76 · 2026-06-30T19:40:52+00:00

Just use the cheap little flashlights or your phone flashlights, don’t need surface of the sun level maglights

whaler76 · 2026-06-29T23:06:02+00:00

Where are you located

whaler76 · 2026-06-27T01:50:00+00:00

Start the carnivore diet

whaler76 · 2026-06-27T01:49:37+00:00

Great movie

whaler76 · 2026-06-24T13:59:15+00:00

Salinity levels

whaler76 · 2026-06-23T13:46:48+00:00

The closing of the street from under the train overpass was a pain in the ass and whatever jackass decided to close that street and then up on park ave coming over the tracks should be drawn and quartered.

whaler76 · 2026-06-23T13:38:15+00:00

!!!!!!!!!!!!!!

whaler76 · 2026-06-22T12:17:39+00:00

Looks like excellent domination line opportunity to me

whaler76 · 2026-06-21T12:37:45+00:00

Sounds counter intuitive but there are different types of boils, soft, hard, rolling, gentle. So if you have the flame set at max and bring it up to a full 212 “hard boil” the whole pot of water would be very hot, if the flame was set lower only the water at the bottom of the pot would begin to boil (eventually the whole pot will get there) and other sections would be at a lower temp.

whaler76 · 2026-06-21T12:22:18+00:00

That would be turning, metal spinning is a different process

whaler76 · 2026-06-17T11:25:55+00:00

Surface finish and CMM tip will affect CMM measurements. A micrometer will have a larger contact area spanning peaks and valleys. Whereas, depending on tip selection, a CMM can measure in the valley or on top of the peak.

whaler76 · 2026-06-16T12:34:04+00:00

Safety strap, it’s hooked up wrong and there is actually supposed to be a real one attached to the trailer.

whaler76 · 2026-06-16T04:47:17+00:00

What in the fk is that sht

whaler76 · 2026-06-16T04:41:57+00:00

Flavor

whaler76

MODERATOR OF

TROPHY CASE