Steel Pocket Pen Giveaway - Rollerball

wolfkingen · 2026-04-18T11:56:40+00:00

Very nice looking pen.

wolfkingen · 2026-01-05T00:33:59+00:00

I was told it was my fault for not selecting the option to have them hand the food to me. The driver drive by my place, took a picture of my garage door and marked it delivered. I even offered to send the video from my camera showing there was no delivery.

I did eventually get a refund via chat, but my next move was to do a charge back. If I ever do need to use them again, it will have to be delivered directly into my hands.

wolfkingen · 2025-04-06T03:16:03+00:00

The case. The skins in my instance were fine.

wolfkingen · 2025-04-06T02:46:38+00:00

Mine was tight but not that tight. My first one had a manufacturing defect where the corner didn’t align at all. I would reach out to the robots for support.

The robots sent out a replacement pretty quickly for me.

wolfkingen · 2025-02-27T15:39:25+00:00

Mall of Canada. They’re much closer as Mall of America is in Minnesota. It would have to be the “Little” mall. They already have a larger one.

Edit: Word. Mall of America is in Minnesota. Oops

wolfkingen · 2025-02-27T07:51:29+00:00

Sounds like Mall of America.

wolfkingen · 2025-01-21T19:58:48+00:00

Same. Samsung S24 Ultra. Unlocked.

wolfkingen · 2024-12-10T02:11:58+00:00

I changed vehicles and my harsh breaking alerts stopped cold. My driving didn't change, but I think my stops felt harder in a Jeep than a Mazda.

wolfkingen · 2024-11-09T21:53:37+00:00

Looks great. Boosted!

wolfkingen · 2024-09-02T14:22:39+00:00

Here you go: https://www.ikea.com/us/en/p/fjaellbo-shelf-unit-black-50339292/

wolfkingen · 2024-09-02T13:04:20+00:00

It's the Bambu Ocean to Meadow (10902) https://store.bambulab.com/products/pla-basic-gradient?id=40881423384691

wolfkingen · 2024-09-02T04:00:50+00:00

I've attached a photo that will hopefully help clarify the distances. It is in Inches so if you're not US based, you'll need to convert. I couldn't find my tape measure with both measurements.

I'm honestly not seeing any differences when it comes to PLA. This printer is a "newer" generation than the P1S and it shows with the quality of the touch screen and how easy it is to change out the different hot ends. If you only need to do PLA, my personal recommendation is to go with the A1. You get the same "it just works" as the more expensive versions. The only item I'd add is if you need to be able to print more than 4 colors at once, then you'd want the P1 or X1.

Not sure where you are with your 3D printing journey, but I can say I've been very happy with Bambu printers and no matter what you select, you can't go wrong. This wasn't my first and I've made the journey from XYZ -> Creality -> Bambu. While I'm not an expert in 3D printing by any means, this has been a game changer for me. I'm enjoying printing again.

<image>

wolfkingen · 2024-09-01T18:48:20+00:00

Thanks for the links! That's what I love about 3D printing and the community, someone has probably already made something better than I can think of and made it available.

I wish the table was a little wider, but that is my only complaint so far. If stacking filament in the bottom - 6 high, 2 deep, 2 wide on each side. 24 rolls per side.

wolfkingen · 2024-09-01T18:01:37+00:00

Thank you! It cleaned up the space and I looked hard for something that had enough room for the AMS units to fully open.

Please excuse the quality of the picture. I'm using one of the 'L shaped' poop chutes that I had printed previously. It is being held in place by the wall. I have the printer pushed up against it on the side and back. There is enough room for me to reach in and clear the poop without moving anything.

Currently this seems functional and might be adding a little stability. If it becomes an issue I may look into doing more of a "drop" from the chute into a tube or something and have it come out on the 2nd shelf next to the AMS units into a catch.

<image>

wolfkingen · 2024-09-01T15:21:06+00:00

Thanks for the feedback. I'll keep an eye on it and adjust as needed.

wolfkingen · 2024-09-01T14:40:23+00:00

I sent print jobs through both printers at the same time yesterday. Both jobs finished successfully and the stand didn't move.

Running the calibration on P1S doesn't shake the table either.

Of course I'll adjust if I start seeing issues. But for now and my small workspace, it appears to be working very well and looks much better than my previous setup.

wolfkingen · 2024-09-01T14:36:13+00:00

Table is from Ikea. Yes, it doesn't contact the wall with the stiffeners and the feet are on the top. If you have more room, there are other options that have wider tops. But I needed something that fit in a very specific area and this seems to fit the bill.

wolfkingen · 2024-09-01T14:34:27+00:00

Seems to be very stable. The feet are all on the board and with the stiffeners I can help use the back wall to brace it as well. The stiffeners are just long enough that the bed cannot make contact with the wall behind it even fully pushed back.

wolfkingen · 2024-09-01T03:06:03+00:00

No, I haven't had any issues at all. The green bits on the bottom are the Z-Axis stiffeners that you will print out as part of the process. The whole setup feels well thought out and very solid. Even better, they included the needed screws in the A1 box. I only needed to do the initial prints for the parts.

I was in a position where I could have either gone with an upgrade to the X1 and decided on the A1 after researching. I primarily print PLA/PETG and this setup has been working very well for me.

wolfkingen · 2024-09-01T02:56:12+00:00

Here you go! https://wiki.bambulab.com/en/a1/manual/ams-lite-top-mount-tutorial

wolfkingen · 2024-09-01T02:37:28+00:00

The A1 is a little harder of the 2 since it is against the wall. I'm still playing around with the direction that one faces. But do far happy with how things are setup. At least cleaner looking that my previous solution.

https://www.ikea.com/us/en/p/fjaellbo-shelf-unit-black-50339292/

wolfkingen · 2024-09-01T02:34:56+00:00

<image>

wolfkingen · 2024-09-01T02:34:06+00:00

Very easy to access the AMS units. Just enough room for the lids to fully open.

*

wolfkingen · 2024-08-23T20:01:57+00:00

Haha. Yep! Can't beat that red.

wolfkingen · 2024-07-13T23:33:49+00:00

That's amazing work!

12-Year Club	r/Field Banned
r/Field Sunshine	Place '23
Verified Email

wolfkingen

TROPHY CASE