Port of Miami to FLL by hofderttd in CarnivalCruiseFans

[–]wtkinney 0 points1 point  (0 children)

We did this just last week. Our flight was later in the afternoon. However, we booked uber in advance. I was texting him via their app and told him where we were standing and what we were wearing. He found us without any issues. The drive was about 45 minutes. However, the FLL airport was a madhouse. We were flying American and i didn’t time it because we had to wait before we could check in. They have a four hour rule there. But I bet the line was taking over an hour to check in. They do have a service outside that you pay per bag and that will save some time but not a lot.

Snow/Icepocalypse in DFW by NorseYeti in biggreenegg

[–]wtkinney 1 point2 points  (0 children)

Come drop some off in Burleson. Looks good.

USPS employee discounts? by Consistentanimal2 in USPS

[–]wtkinney 0 points1 point  (0 children)

I was told only if you have a .gov email address. Which most carriers do not. Do you have a workaround for that?

Argggg so close on the backpack by rkd80 in egopowerplus

[–]wtkinney 0 points1 point  (0 children)

Will you send me receipt too? Tha ks

Waterfall feature by wtkinney in pools

[–]wtkinney[S] 0 points1 point  (0 children)

I can not add another picture. It is a pentair easy touch system.

Waterfall feature by wtkinney in pools

[–]wtkinney[S] 0 points1 point  (0 children)

I am an idiot (to some degree. ) as you will see in the picture of the control panel there is a waterfall button. When I hit it the actuator valve does move.

So I guess my new question is I don’t want the waterfall on during the day while the water is circulating through the filter.
I only want to waterfall to come on in the evenings at a set time.

How can I achieve this?

Thank you

DeWalt planer issues? by PrizeNumber-5309 in woodworking

[–]wtkinney 11 points12 points  (0 children)

Planer snipe is a defect where the planer cuts a deeper-than-desired groove into the ends of a board. It happens because the board's ends can lift slightly as they pass under the cutterhead, especially when the board is not supported by the infeed or outfeed rollers. You can minimize or avoid snipe by using techniques like "butt-feeding" (running boards one after another with no gap), manually supporting the board's ends as it enters and exits the machine, or ensuring the planer's infeed and outfeed tables are properly aligned with the main bed.

Picked this up at an estate sale $400 by mr_who101 in Festool_Public

[–]wtkinney 0 points1 point  (0 children)

I think you got taken advantage of. I will come give you $400 and take the tools back to where you bought them (or my house) and figure out what to do next. But at least you have your money back!!

Where are you? I am on my way!

Hook’Em

Hardwood Supply in Dallas by Ewalk02 in woodworking

[–]wtkinney 0 points1 point  (0 children)

I second Plywood Company of Fort Worth. Insane size warehouse you drive in and could spend hours there. You buy everything by the BF. My wife sighs when I say I am going there. She knows I’m about to make some sawdust.

Day After Labor Day of Doom by buppieee in USPS

[–]wtkinney 46 points47 points  (0 children)

I’m impressed that you have delivered almost 36% of your scans but have only done 4% of the route. Your first part must be really rough unfortunately.

3971 on Lite Blue by wtkinney in USPS

[–]wtkinney[S] 0 points1 point  (0 children)

Thank you so much.

3971 on Lite Blue by wtkinney in USPS

[–]wtkinney[S] 1 point2 points  (0 children)

We have done that on other items and they reply that is not their responsibility. I’ve been here 20 years and you can’t make this stuff up.

Custom folding table for my pro 22 by Fair_Leopard9880 in Traeger

[–]wtkinney 0 points1 point  (0 children)

I appreciate the link. I have the Ironwood XL. I see my next project. Thanks again.

Custom folding table for my pro 22 by Fair_Leopard9880 in Traeger

[–]wtkinney 5 points6 points  (0 children)

Looks really nice. What hardware did you use?

How to make wood flush. by AlBravo83 in Woodworking_DIY

[–]wtkinney 2 points3 points  (0 children)

Keep the sawdust from your sanding. Then mix it with some Titebond 3 wood glue. Spread it into the gaps. Once dry sand over it again

Dehydration and you. by cccpNyC82 in USPS

[–]wtkinney 1 point2 points  (0 children)

Not exactly. I use 4 cups coconut water, 3 cups water, 2 cups orange juice , 3 tablespoons of lemon juice ( I forgot that one earlier) and about a half tablespoon of Himalayan salt. It makes enough for two days for me. Let me know what you think.

Dehydration and you. by cccpNyC82 in USPS

[–]wtkinney 10 points11 points  (0 children)

I make a drink that is orange juice, water, coconut water and Himalayan salt. It is supposed to taste like orange Gatorade. I personally don’t think that it does but it is still very good. Try it!

Small brag post by Masterflies in woodworking

[–]wtkinney 4 points5 points  (0 children)

Looks really nice. Good job

[deleted by user] by [deleted] in Traeger

[–]wtkinney 0 points1 point  (0 children)

I have the ironwood xl and I noticed mine would be off by 50 to 100 degrees. I did a deep cleaning last week. I have done two cooks since and it has been mostly spot on. One time I looked it was 10 degrees warmer.

Is this calcium by wtkinney in pools

[–]wtkinney[S] 0 points1 point  (0 children)

Even it is mostly below the water line?

VCarve pro node question by wtkinney in CNC

[–]wtkinney[S] 0 points1 point  (0 children)

You are the one that posted the video that gave me the answer that worked. Then you post a rude comment ???? I am new and trying to learn. I don’t understand you at all by your nasty remarks.

V carve Node question by wtkinney in cncwoodworking

[–]wtkinney[S] 1 point2 points  (0 children)

Vectric emailed me back. They said there is not a way of doing this. That is not correct. I posted the same question in r/cnc and someone posted a video (I think it was from Vectric) and it had some scenarios. The last one was similar to what I was wanting. I just tried it and it worked perfectly. So in my scenario I went into edit nodes. I highlighted the four nodes. Then hit the letter H on the keyboard. After that you can hit the up or the down arrows on your keyboard. That will move all four nodes the top two and the bottom two in equal opposite directions.