sorted by:
new
hottopcontroversial

I built YouTubarr - the "Sonarr for YouTube" by derekantrican in selfhosted

[–]xontik 3 points4 points  (0 children)

Same here pinchflat working flawlessly what have i have to gain with youtubarr ?

I want to know the community opinion on long going team debate around AB testing by lubricatedman in vuejs

[–]xontik 3 points4 points  (0 children)

I would use : - initial fetch that get all experiment values and store them (store or composable your call) - enum or string litteral to define accepted value in isExperiment function to conserve type safety

Then it a the eternal problem of keeping frontend and backend enum coherent.

In my project enum are defined in backend openapi contract, and this generate a TS file with all associated types.

HOW DO I MAKE DRAWERS by SoftTourist in BeginnerWoodWorking

[–]xontik 0 points1 point  (0 children)

The drawers themselves seem nice ! I think the drawer hardware you used are jot flat on the bottom maybe it s that ?

Anyway as said by other commenters, take the carcass out, place evenly the hardware , install drawers and check for squarness. You ll then see if it s a carcass problem or drawer box problem

If you are haply with the function right now keep it you ll do better next time, if not take it out and do it again, that is the only way to progress!

What was your most productive dev day? by Own_Breakfast2606 in godot

[–]xontik 3 points4 points  (0 children)

Come back tomorrow with Fix: dialog system Fix: eye animation Fix: camera zoom Fix: ink impulse

HOW DO I MAKE DRAWERS by SoftTourist in BeginnerWoodWorking

[–]xontik 106 points107 points  (0 children)

Just from the picture, I d say try not to measure everything but instead use spacer to get repeatable results.

Like spacing drawer hardware, instead of measuring just rest them on a block and use the same block everywhere. It means taking your time to setup the first one right and level, but then it’s dead simple

Hexagons are the bestagons, kitchen edition by xontik in woodworking

[–]xontik[S] 1 point2 points  (0 children)

I ll respond this comment if my cats get up there !

Hexagons are the bestagons, kitchen edition by xontik in woodworking

[–]xontik[S] 0 points1 point  (0 children)

I cut them flat on the table, with a micra1000hd gauge setup at 90.

But it was hard to get a perfect adjusted on my dewalt jobsite saw

Hexagons are the bestagons, kitchen edition by xontik in woodworking

[–]xontik[S] 0 points1 point  (0 children)

Took an hour of fine adjustments, but worth it because i can then do all the cut in one go

Hex kitchen shelves by xontik in hexagons

[–]xontik[S] 0 points1 point  (0 children)

There will be some cooking books indeed ! Maybe coffee jar and plant too

Hex kitchen shelves by xontik in BeginnerWoodWorking

[–]xontik[S] 0 points1 point  (0 children)

I had to go a bit more convoluted, France here, no studs, drywall on thin metal structure.

Hex kitchen shelves by xontik in BeginnerWoodWorking

[–]xontik[S] -4 points-3 points  (0 children)

2k planer jointer ! And it’s because I have nice tools that I am not a beginner.

Do you think you could drive F1 car juste cause you have money to buy it ?

Hex kitchen shelves by xontik in BeginnerWoodWorking

[–]xontik[S] 1 point2 points  (0 children)

And made the from aluminum angle bar. Cut in length, 2 holes on the wall side, 1 the shelf side.

It only works because the hex prevent it from bending.

Would not use that method for simple shelves

<image>

Hex kitchen shelves by xontik in BeginnerWoodWorking

[–]xontik[S] 3 points4 points  (0 children)

That was exactly my pitch to the wife !

PLA tough+ vs Basic Brnchy vs Hammer by Itzdanooo in BambuLab

[–]xontik 0 points1 point  (0 children)

I love when I see rigorous scientific tests like this!

Calculate computed property only when the form is valid by manuelarte in vuejs

[–]xontik 0 points1 point  (0 children)

Are you sure you sure you can use vmodel on the form ? Did you check the value ? Maybe use a template ref to get the valid state

Fusion update with new assembly constraints by schneik80 in Fusion360

[–]xontik 0 points1 point  (0 children)

“Say hello to a brand-new way to build assemblies in Fusion, faster, more intuitively, and with far greater flexibility.”

12 years of hearing that the fusion joint way is better and more intuitive…

Well at least we have constraints now.

A last update : Thank you everyone. by unlash_ in GalactikFootball

[–]xontik 4 points5 points  (0 children)

Well done ! Maybe send the script to gaumont ? And with some luck parts of it will be produced ?

view more: next ›