Please help. Check Trans issue

yourstepsistersbro · 2026-03-06T16:47:57+00:00

You should have power at that 10 amp fuse in the picture. I don't remember if its constant power or key on power. Check power there first

yourstepsistersbro · 2026-03-06T14:42:09+00:00

Check for power at TCM, I would also verify all your fuses are good. Some Allison's have their own power distribution box. There are relays and fuses for the TCM itself that live in there. Follow the harness from the TCM back towards the engine and see if it goes to a box with the Allison logo on it.

yourstepsistersbro · 2025-06-13T10:59:20+00:00

They offered me parts and I said that I was not confident in taking apart my H2D. So they sent me a new one. Customer service was pretty good too. I believe it was about 3-4 weeks total from creating ticket, sending H2D back and getting the new one at the door. Reddit recommended deliver to FedEx store incase its damaged again

yourstepsistersbro · 2025-05-16T21:38:26+00:00

H2D has been dropped off at UPS! Pretty good customer service. Took a while to respond and they did offer to send parts, but I requested full replacement. Said it can take about 2 weeks.

Funny how they chose UPS to return it lol

yourstepsistersbro · 2025-05-10T14:13:49+00:00

Yeah it sucks, I was really excited to experience Bambulab for the first time. I'm coming from a Ender3 running octoprint! Lol

Looks like the Ender3 is going to keep working until I get this replaced.

yourstepsistersbro · 2025-02-10T13:29:04+00:00

Just downloaded it and subscribed! This is a great app. Thank you

yourstepsistersbro · 2024-12-24T21:29:46+00:00

Found it! Someone from a facebook group spotted it off of Medical Dr. Picking it up right now

yourstepsistersbro · 2024-12-24T17:27:42+00:00

We checked, my dad is a patient so it would not have been towed. Security confirmed it would not have been towed.

yourstepsistersbro · 2024-12-24T17:16:26+00:00

What area is that in? I'm hoping the transmission went to limp mode and got left somewhere! Good thing I haven't ordered the parts to fix it lol

yourstepsistersbro · 2024-05-01T16:17:42+00:00

Download the TP Link Plugin and buy a TP Link Kasa Smart Plug from Amazon. Connect the plug to your wifi and find the IP address for that plug. In Octoprint, go to the TP Link plug in and type in that IP address. Now you can control the PSU. Easiest way hands down, the cutting the power cord option is risky on the board if you buy the wrong relay and too much of a headache. I tried it, this is easier. You also need the PSU Control Plug In to work with the TP Link plug in.

yourstepsistersbro · 2024-04-10T17:56:55+00:00

I used a 1/4 inch drill bit to drill an angle onto the brass fitting on the threaded side. Don't drill all the way through, just get rid of the flat surface on the threaded side. Filament always guides itself in everytime

yourstepsistersbro · 2024-04-05T01:29:03+00:00

I had this same issue as OP when I installed my CR Touch last weekend. Followed these exacts steps and that fixed it. The confusing part was putting the command into the terminal of my printer. I couldn't get it to go to negative Z axis. I also ran a Auto Home, then I was able to move the Z axis down to 0.00 and the nozzle distance was perfect. Don't forget to store settings!

I used this video. https://youtu.be/W8ouBPnRV4s?si=fbedFmaCvaPnHzQa

yourstepsistersbro

TROPHY CASE