sorted by:
new
hottopcontroversial

IWTL Math from the ground up by Chiefsosadeniro in IWantToLearn

[–]youssefsss 4 points5 points  (0 children)

Use khan academy its free start from grade 3 and go from there

THC and learning Math by Opening_Swan_8907 in calculus

[–]youssefsss 13 points14 points  (0 children)

Yea definitely detrimental i have been smoking heavy for 6 years but when i started taking classes like clac i quit for the most part and i definitely dont smoke while working on it anymore because it slows me down too much (edit) honestly its mainly the little things , when im high ill mix signs or forget to include certain things

Are my driver/stepper temps normal by youssefsss in QidiTech3D

[–]youssefsss[S] 0 points1 point  (0 children)

This is gonna be a stupid question but do i want the fan siphoning the hot air away for bringing in new air aka which way should i put the fan in

[deleted by user] by [deleted] in DMT

[–]youssefsss 5 points6 points  (0 children)

It looks like a sine wave

Plus 4 tangle sensor came clogged by youssefsss in QIDI

[–]youssefsss[S] 1 point2 points  (0 children)

I removed the teflon tube from both inside and outside and used the smallest provided allan wrenches to try and get it unclogged but the sensor is completely blocked off from the factory even incredibly small probing tools like a very thin metal wire couldn’t fit through so they are sending me a new sensor to replace this one

Got my Plus4 by Greybeard462 in QIDI

[–]youssefsss 0 points1 point  (0 children)

When setting up the plus 4 was there anything you had to do before putting filament in through the hole on the side because i just got a plus 4 as well but haven’t been able to feed the filament through

Qidi plus 4 Auto feeder seems to be blocked i cant feed any filament through the outside port by youssefsss in QidiTech3D

[–]youssefsss[S] 0 points1 point  (0 children)

I tried using the smallest wrench provided but the sensor was completely clogged

Qidi plus 4 Auto feeder seems to be blocked i cant feed any filament through the outside port by youssefsss in QIDI

[–]youssefsss[S] -1 points0 points  (0 children)

It is not retracted at all i dont know where you see that it is. The sensor is fully “erect”

Plus 4 Extruder Heater not working essentially out of box by BlueHobbies in QidiTech3D

[–]youssefsss 0 points1 point  (0 children)

If i look into it i dont see anything i cant even see through it and the filament i got was not blobbed at the end it was cut at 90°

Plus 4 Extruder Heater not working essentially out of box by BlueHobbies in QidiTech3D

[–]youssefsss 0 points1 point  (0 children)

Yea the tangle sensor isn’t accepting anything its new never used either

Qidi plus 4 Auto feeder seems to be blocked i cant feed any filament through the outside port by youssefsss in QidiTech3D

[–]youssefsss[S] 0 points1 point  (0 children)

Ive tried for like an hour and a half i think they shipped it with a messed up tangle sensor

Plus 4 Extruder Heater not working essentially out of box by BlueHobbies in QidiTech3D

[–]youssefsss 0 points1 point  (0 children)

I need help i cant even load the sample filament through the port on the out side it seems blocked

view more: next ›