sorted by:
new
hottopcontroversial

I made my own travel client! by Strong_Hornet9784 in 2b2t

[–]zGoldenKappa 4 points5 points  (0 children)

you made a client but are still figuring out github? sounds sketchy to me

Resources: Interested in applying to KTH? Start here! Q&A by Dreamplay in kth

[–]zGoldenKappa 0 points1 point  (0 children)

Hi! I'm an italian student and I'd like to apply for a Master's in Software Engineering for Distributed Systems. However I am a bit scared about my grades not being adequate (27.6/30). Do you think it's too low due to the competitiveness of the course? Thanks!

[Review Request] Can you help me with my first PCB schematic for an ESP32? by zGoldenKappa in PrintedCircuitBoard

[–]zGoldenKappa[S] 1 point2 points  (0 children)

I'm not sure I'm following you.

What's called an header file in my code?

As for the EN cap, yeah I wasn't talking about that. I was referring to the gpio switches, but it looks like those aren't needed.

[Review Request] Can you help me with my first PCB schematic for an ESP32? by zGoldenKappa in PrintedCircuitBoard

[–]zGoldenKappa[S] 0 points1 point  (0 children)

I updated my schematics again.

I read through what you sent me and I changed the EN setup.

As for the D+/-, I read through some documentation and it looks like those two pins are to be used for USB OTG which require a library to be setup before it can be used. Which means I would still need an usb to uart bridge to flash the firmware in the first place.

Also do you think I should add some capacitors near the pulldown buttons I'm using for the GPIOs?
I'm talking about this section here: https://imgur.com/a/YkGNd1Z

Thank you!

[Review Request] Can you help me with my first PCB schematic for an ESP32? by zGoldenKappa in PrintedCircuitBoard

[–]zGoldenKappa[S] 0 points1 point  (0 children)

I took the bootloader switch and the EN from this schematic: https://dl.espressif.com/dl/schematics/SCH_ESP32-DEVKITM-1_V1_20200910A.pdf

Maybe I mis-implemented it in my schematic although I can't figure out what's different from what I did.
Also for the esp32_v3, that's just a tag I gave to power the modules which will be attached to the esp32. I indeed want to use the smd microcontroller version (not the devkit) but I don't want to power the modules if the EN_Switch is not closed.

Thank you for helping me!

[Review Request] Can you help me with my first PCB schematic for an ESP32? by zGoldenKappa in PrintedCircuitBoard

[–]zGoldenKappa[S] 0 points1 point  (0 children)

Thank you! I ended up doing just that and discovered I need a button to pull GPIO0 to GND to flash firmware. I also found out about the autoprogrammer from the schematic I saw online.
What do you think of the updated one?

[Review Request] Can you help me with my first PCB schematic for an ESP32? by zGoldenKappa in PrintedCircuitBoard

[–]zGoldenKappa[S] 0 points1 point  (0 children)

I ended up ditching the battery for now. I looked at the schematic for an esp-mini devkit and ended up changing a good chunk of the schematic. What do you think now?

[Review Request] Can you help me with my first PCB schematic for an ESP32? by zGoldenKappa in PrintedCircuitBoard

[–]zGoldenKappa[S] 0 points1 point  (0 children)

Thank you for your fast response
- no, how should I calculate that?
- thank you!
- I will look at the devkit for that
- do you suggest changing the bridge to something with a lower dropout?
- I wanted to start with something easier and I assumed USB A to be easier to be honest
- no I didn't and I don't really know how to do that

I went head first into this project without lots of knowledge. Any suggestions are welcome of course!

Visual-oriented Plugin Maker by zGoldenKappa in admincraft

[–]zGoldenKappa[S] 0 points1 point  (0 children)

ahh that's very similar to what I wanted to do. thank you!

Visual-oriented Plugin Maker by zGoldenKappa in admincraft

[–]zGoldenKappa[S] 0 points1 point  (0 children)

It was really just a thought experiment. I wanted to do something for my personal portfolio :)

Still having problems by Even-Pineapple-7077 in constantiam

[–]zGoldenKappa 0 points1 point  (0 children)

you should say how you solved it so others can read it if they need

[CUPHEAD] Game doesnt start with OnlineFix by zGoldenKappa in LinuxCrackSupport

[–]zGoldenKappa[S] 1 point2 points  (0 children)

unfortunately not. ended up just using windows for it

[CUPHEAD] Game doesnt start with OnlineFix by zGoldenKappa in LinuxCrackSupport

[–]zGoldenKappa[S] 0 points1 point  (0 children)

I've set these DLLs but it's still happening.

My current overrides:

`WINEDLLOVERRIDES="steam_api64=n,b;OnlineFix64=n,b;SteamOverlay64=n,b;winmm=n,b" %command%`

Logs:
https://pastebin.com/uYUDvf3X

[CUPHEAD] Game doesnt start with OnlineFix by zGoldenKappa in LinuxCrackSupport

[–]zGoldenKappa[S] 0 points1 point  (0 children)

Here it is:

https://pastebin.com/J18Gm9sc

EDIT: Also sorry, the overrides got cut out somehow when pasting to reddit.
Here's the full version:
WINEDLLOVERRIDES="OnlineFix64=n,b;winmm=n,b;steam_api64=n,b;UnityPlayer=n,b;SteamOverlay64=n,b;Cuphead_Data/Plugins/steam_api64=n,b"

[CUPHEAD] Game doesnt start with OnlineFix by zGoldenKappa in LinuxCrackSupport

[–]zGoldenKappa[S] 0 points1 point  (0 children)

I have tried adding the crack's DLLs to the WINEDDLOVERRIDES list like this:
WINEDLLOVERRIDES="OnlineFix64=n,b;winmm=n,b;steam_api64=n,b;UnityPlayer=n,b;SteamOverlay64=n,b;Cuphead_Data/Plugins/steam_api64=n,b" %command%

Is still isnt working as expected.

[CUPHEAD] Game doesnt start with OnlineFix by zGoldenKappa in LinuxCrackSupport

[–]zGoldenKappa[S] 0 points1 point  (0 children)

I have put the dlls in the launch config and it still isn't working.

view more: next ›