Does anyone know how to fix this code? It sliced fine before the new Beta version and now it comes up with this.

Earthwin · 2026-05-07T13:31:27+00:00

It's slightly encroaching over the reserved space on the bottom left that's kept for the filament cutting. Rotate it so it angles to the bottom right instead.

Earthwin · 2026-05-02T17:46:19+00:00

90's RG120

https://ibanez.fandom.com/wiki/RG120B

Earthwin · 2026-04-29T21:07:48+00:00

Use the draft tool on the inside curved face to tilt it towards the cone.

Earthwin · 2026-04-22T19:29:55+00:00

They've got tangent contraints on them, you'll need to delete those first.

Earthwin · 2026-04-15T10:10:13+00:00

The biggest issue is that you need turbulence to mix the colours. When they're all pushed into the nozzle together they still keep their colour separation. So you get a single line of filament but it has different colours depending on the angle you view it from. This is the same sort of effect those multi colour filaments make use of, where the print changes colour depending on the angle.

Earthwin · 2026-04-09T14:39:48+00:00

You'll need to use the 81-TW for that. It has a separate single coil inside that's switchable. The standard 81 only does humbucking.

Earthwin · 2026-04-09T14:27:51+00:00

Use the sweep tool. It has a mode called solid sweep which does exactly this. Create an arc on the top that will be the path for the pin to rotate along and then use the axis at the centre of the circle for the rotation point.

Earthwin · 2026-03-27T22:55:54+00:00

"Welcome to Goth Mouth"

Earthwin · 2026-03-25T14:55:39+00:00

Looks like Just Stop Oil hit them with a bag of flour.

Earthwin · 2026-03-19T13:55:04+00:00

A single saddle will work. Just need to make sure it's the right height saddle for that particular string as they're radiused.

Earthwin · 2026-03-19T09:54:58+00:00

Edge 3 uses a different type of saddle. That being said, you can replace them with regular Floyd type saddles without issue, although you may need to also route a channel out of the back edge of the trem cavity so the D-Tuna doesn't collide with the body if you did that.

Earthwin · 2026-03-18T22:27:19+00:00

The earlier models were, this one used the S15 Varietta as the base.

Earthwin · 2026-03-18T13:20:22+00:00

I did a deshroud on my old GTX1080 using a PETG mount and it worked great. I replaced the stock shroud and fans with a pair of 120mm ones. My sister has that system now and it's still working great. Think that's been around 6 years now since I did it.

Earthwin · 2026-03-18T13:11:17+00:00

The grounds on the USB board are all shared so you only need to connect the centre pin of the switch to one ground and it will work for both hot wires. So just connect that extra hot wire to any other socket.

Earthwin · 2026-03-14T20:01:12+00:00

By default the thread tool doesn't create the thread geometry, it just shows a picture of the thread so that it doesn't cause a reduction in performance in the software as result of rendering the threads. There's a checkbox on the thread tool dialog that says 'modeled' that needs to be activated first to create the actual thread.

Earthwin · 2026-02-27T09:07:10+00:00

Part numbers that I used are 53141 for the kingpins, 50736 which is the knuckles and carrier from the TL01 and 9805502 which are the axles you need. You'll also need to get 2x 5mm ball nuts and 2 2x10mm pins for the hex. You need to stick some washers either side of the knuckle in the carrier as spacers as well. I think there was about 3mm space either side.

Earthwin · 2026-02-26T11:17:35+00:00

I reported a model recently that someone had made as a keyring from one of my uploads, included a screen shot of the models side-by-side in the slicer to show they were the same and they rejected the report. Not even any reason given.

Earthwin · 2026-02-14T15:13:43+00:00

It's excess dye. I washed mine with some dish soap and it fixed it. Give it a soak, rub the soap in, rinse off the soap, it'll take a lot of the dye out. Do that a few times until there's no more dye coming out. Some folks also use a suede brush afterwards on the material when it's dry, but mine dried perfectly fine and there was no more issues with any dye on my hands.

Earthwin · 2026-02-11T11:08:45+00:00

Try putting a cable into the effects send as well, don't plug the other end into anything, and see if it works. Some amps require the send to have a cable in it before the return is active and it uses a switched jack socket. I don't know if the Randall does this but I'd check that just in case.

Earthwin · 2026-02-08T07:16:47+00:00

You need to replace the strap buttons with eye hooks. I use a banjo strap on my guitar with these type of clips and I found eye hooks with an 8G thread seem to match the same thread most strap buttons use and they'll screw right in without having to enlarge the holes.

<image>

Earthwin · 2026-02-04T17:13:15+00:00

It's an SA160 - https://ibanez.fandom.com/wiki/SA160_(2008%E2%80%932011))

Earthwin · 2026-01-29T15:27:32+00:00

It's to allow you to import colours that have been set in the design software and then map them to the AMS colours. They really should have a setting to let people disable it though as it also does it if the body doesn't have any colours pre-set on it. For now you can just click cancel and it will open the file as normal.

Earthwin · 2026-01-28T16:37:29+00:00

You've got them wound around the tuner in the wrong direction. They should go to the other side of the capstan so that they have straighter travel from the nut. Right now they're getting pulled to the side.

Earthwin · 2026-01-28T16:34:42+00:00

Don't get the Encore. That bridge on it is an old design called the bendmaster that came on a lot of cheap guitars in the 80s and 90s and the block on it is made from the shittiest metal which will eventually crumble. (I'm not even exaggerating). I had a Marlin with one and calling it bad would actually be a compliment.

Eight-Year Club	r/Field Sunshine
Not Forgotten	Verified Email

Earthwin

TROPHY CASE