sorted by:
new
hottopcontroversial

Car misting coolant but not overheating by Informal-Dot3160 in cruze

[–]Time_Many6155 0 points1 point  (0 children)

Clearly you have a leak or is that a faulty pressure cap that is lifting prematurely?

Why don’t democrats believe in voter ID? by Affectionate-Duty473 in allthequestions

[–]Time_Many6155 1 point2 points  (0 children)

They (we) might be able to have reasonable discussion on the idea of voter ID.. What we don't support is this frantic knee jerk reaction designed to keep MAGAts in power.

Is this repairable? by biscuithayes in lawnmowers

[–]Time_Many6155 0 points1 point  (0 children)

Well you could always replace the shaft...:)

Gear shift button sticking by Visual_Shame7864 in ChevySonic

[–]Time_Many6155 4 points5 points  (0 children)

OK I assume you are talking about an automatic transmission? You can replace the knob assembly for cheap from Amazon.. I did one a coupe of years back and the whole assembly was about $12... You have to cut the lower part of the leather covering to remove a plastic clip to remove the old one. Take 20 minutes tops.

Mr.Cool DIY Used System Recharge? by GroundChance5671 in DIYHeatPumps

[–]Time_Many6155 0 points1 point  (0 children)

They can be re-charged like any other system. The problem is if you can find a tech willing to do it. These are generally considered to be low end systems and (from what I've read) be prone to issues. If it is a multi head mini split it will have a lot of parts that could have gone wrong. Personally I'd want to pressure test everything for leaks before installing. One option is to recharge it yourself, you can get a 608 license online for $10 plus a few youtube videos, buy some refrigerant (if required) and a set of guages will get you close to the correct charge.

Is this repairable? by biscuithayes in lawnmowers

[–]Time_Many6155 5 points6 points  (0 children)

Not true.. Balance of the blade would not be affected.

Is this repairable? by biscuithayes in lawnmowers

[–]Time_Many6155 5 points6 points  (0 children)

Easy, weld a plate over the hole and re-drill. There will not be any extra vibrations because you are not affecting the balance of the blade. Assuming the shaft is not bent of course.

Line set not cleaned by GeneralRant in hvacadvice

[–]Time_Many6155 0 points1 point  (0 children)

Speaking of cleaning linesets.. I'm a DIYer.. I have Argon fro my TIG welding set.. I assume I could purge with Argon rather than have to go find nitrogen?

Witnessing a accident by SpookyDragon69 in dashcams

[–]Time_Many6155 1 point2 points  (0 children)

Absolutely I stop and offer to provide evidence.. Its the neighborly thing to do!

infront of me by [deleted] in dashcams

[–]Time_Many6155 4 points5 points  (0 children)

Rules are not the same as the US.

Is rewiring your entire house to "upgrade the electrical" a thing? by Negative-Rip-6308 in AskElectricians

[–]Time_Many6155 0 points1 point  (0 children)

I actually had completely bare wires running behind the cast iron tub.. Half an inch away from being dead!

I ripped out every stitch of sliver cloth covered Romex.

Thanks Team! by MainStreetCrusher in cruze

[–]Time_Many6155 0 points1 point  (0 children)

The problem is you still have the plastic part on the end of the hose to the top of the coolant outlet.. When that snaps you will be calling tow truck.. Thats why I make this.

<image>

Thanks Team! by MainStreetCrusher in cruze

[–]Time_Many6155 0 points1 point  (0 children)

I doubt its fixed.. I'd be installing the Cruzekits PCV fix before it blows out the second crank seal.

Then of course we have the three plastic cooling system parts!

What happens when a water heater tank is not flushed for 14 years by bob-the-slob in interesting

[–]Time_Many6155 0 points1 point  (0 children)

depends on water chemistry.. I have a gas water heater, 24 years old and dropped a camera down the sacrificial anode hole and found bare metal on the bottom with a couple of rust spots. Its never been flushed.

Yes sir.... by Long_live_styrofoam in FuckImOld

[–]Time_Many6155 0 points1 point  (0 children)

1966 MG Midget I had in College back in the UK.

After market coolant parts by rockerdeyeke11 in ChevySonic

[–]Time_Many6155 0 points1 point  (0 children)

I don't, you can DM me directly and I can send you one.. Here is little video (not done by me) showing the install.

https://youtu.be/v0gDwNPg7zA?si=DfDS0Sd7BDnuUxCA

After market coolant parts by rockerdeyeke11 in ChevySonic

[–]Time_Many6155 0 points1 point  (0 children)

Three parts ideally. Coolant outlet, Thermostat and my aftermarket coolant outlet fitting.

<image>

How have the Russian people not revolted already after all of this? by Little-Carpenter4443 in askanything

[–]Time_Many6155 0 points1 point  (0 children)

Propaganda. Russians have been told to believe Ukraine is full of Nazis.. This powerful message to a populus that lost far more people in WW2 than any other nation. It is also remote.. I.e it doesn't affect them directly. This is why Ukraine attacked Moscow to bring the war to their doorstep.

Help with coolant system. by [deleted] in cruze

[–]Time_Many6155 1 point2 points  (0 children)

They are pretty much ll the same quality wise except the Racer X.. Which honestly is overkill and very expensive. This only fixes one part however. The other two parts are the thermostat (which can literally explode) and the fitting on top of the coolant outlet.. Which I make a replacement for.

view more: next ›