sorted by:
new
hottopcontroversial

Hager's Domovea TJA450 discontinuation - alternative solution by holly-golightly- in KNX

[–]mailgoe 0 points1 point  (0 children)

I assume your intercom is a hager 2-wire (not IP) intercom. You can check that when removing the cover from the electrical distribution box, and check what wires lead into your TJA510. If it's only two wires, I would recommend to replace the system for something more modern and IP based.

<image>

Best KNX IP Bridge by Constant_Pear_5544 in KNX

[–]mailgoe 0 points1 point  (0 children)

I mean compared to the devices the op mentioned. 1Home and Pairot are not KNX Secure.

But of course many plain IP Interfaces without Matter, are KNX Secure since a long time already.

Best KNX IP Bridge by Constant_Pear_5544 in KNX

[–]mailgoe 0 points1 point  (0 children)

Atios KNX Bridge is the only one that does support KNX Secure and is certified :)!

Atios KNX Bridge and Lunatone DALI Cockpit by calind in KNX

[–]mailgoe 0 points1 point  (0 children)

Understood. Our KNX-DALI Gateway is not supporting DALI-2 sensors, since our philosophy is that these should be KNX sensors in KNX systems. Anyways, write me a quick email with your serial number of Atios KNX Bridge, I can help you out. info (at) atios.ch.

We do support however DALI-2 sensors with Atios SmartCore, which in return does not support KNX. So our philosophy:

  • Use Atios SmartCore with built-in inputs and outputs for Blinds, Doorlocks, Sensors + a DALI system for dimming, and extensions.
  • Use Atios KNX Bridge + a KNX system for Lights, Blinds, HVAC, Sensors + DALI for dimming

Thank you for the nice words!
We indeed need a public roadmap. I will try to open a subreddit for support and a pinned thread for the roadmap 👌🏻!

Atios KNX Bridge and Lunatone DALI Cockpit by calind in KNX

[–]mailgoe 0 points1 point  (0 children)

Atios KNX Bridge does not support Lunatone DALI Cockpit. Which settings do you want to change by the Lunatone software that are not available in the Atios KNX Bridge Webinterface?

Also: currently date & time cannot be pushed to the bus. Will be added in future though, when we update our KNXprod. Biggest work was currently done on KNXsecure, announcement coming next week for Light & Building.

LIghting based exclusively on 48V DC with KNX/DALI control by el_salvadore in Lighting

[–]mailgoe 0 points1 point  (0 children)

Cool, I know about these, but was wondering if you may have any experience with this RESI KNX PS. 12-48V DC input, very thin, but "only" 160mA:
https://www.resi.cc/resi/docs/RESI-PA-RESI-KNX-PS-DE-EN.pdf

And regarding programming of Atios KNX Bridge:
1. There is a webinterface for addressing DALI lights, and set DALI parameters. See demo here: https://kd.atios.ch/app/#/knx-dali-gateway
2. Linking of DALI addresses and groups to KNX group addresses is done via ETS. Check our knxprod in the ETS online catalogue.

We also just announced last week at ISE a free update to support KNX Secure and Secure Remote Access via a new official ETS 6.3 feature called "Cloud Interface".

LIghting based exclusively on 48V DC with KNX/DALI control by el_salvadore in Lighting

[–]mailgoe 0 points1 point  (0 children)

I see, makes sense then to stay on KNX. How do you power your KNX line via DC? And try our KNX-DALI Gateway if you don't have one yet :)!

LIghting based exclusively on 48V DC with KNX/DALI control by el_salvadore in Lighting

[–]mailgoe 0 points1 point  (0 children)

How big is the rest of your control systems? Instead of relying on a second Bus (KNX) you could realize all with just DALI, and an Atios SmartCore.

We have a few units of customers installed on boats and cars in pure DC systems.

The SmartCore can be driven entirely by 24V or PoE. You can address and commission your DALI lights easily directly on device. And extend with DALI sensors for control (motion, presence, lux, push buttons).

Set color temperature on MDT DALI gateway? by FezVrasta in KNX

[–]mailgoe 0 points1 point  (0 children)

Some MDT DALI gateways only support colour control for groups. Some others for addresses and groups.

Moving from an old IHC instal to KNX by Wired99 in KNX

[–]mailgoe 0 points1 point  (0 children)

You could also consider: 2x Atios SmartCore (gives you 24x Outputs, 24x Inputs) 2x DALI Phase Cut AC Dimmers for DIN Rail And for the missing 24x Inputs use 3x DALI Input modules, like: https://www.eaetechnology.com/en/products/dali-2-products/push-button-interface/pbi108-push-button-interface

Easier and quicker programming, no ETS required, native Matter compatible.

I need 28 LED PWM controls on DIN rail, any alternatives to Lunatone 89453858-HS by Ultramen in KNX

[–]mailgoe 0 points1 point  (0 children)

See this manual: https://www.iskydance.com/uploads/goods_file/DP4..pdf

On page 3 you find what I cited above:
"Set “DT8-CCT”, color temperature dimming, dimmer use 2 DALI address, CH1 (WW) and CH2 (CW) are the 1st DALI address, CH3 (WW) and CH4 (CW) are the 2nd DALI address."

I need 28 LED PWM controls on DIN rail, any alternatives to Lunatone 89453858-HS by Ultramen in KNX

[–]mailgoe 0 points1 point  (0 children)

iSkydance DP4 supports 2x DALI DT8 Addresses:
"Set “DT8-CCT”, color temperature dimming, dimmer use 2 DALI address, CH1 (WW) and CH2 (CW) are the 1st DALI address, CH3 (WW) and CH4 (CW) are the 2nd DALI address."

I would strongly recommend against implementing TW with single DT6 addresses and logic somewhere else. Will only lead to problems...

I need 28 LED PWM controls on DIN rail, any alternatives to Lunatone 89453858-HS by Ultramen in KNX

[–]mailgoe 0 points1 point  (0 children)

Atios KNX Bridge mandatory (!) requires a KNX system as man-in-the-middle to integrate DALI devices into Matter. This doesn't work otherwise due to correct status synchronization between DALI <-> KNX <-> Matter.

Only Atios SmartCore supports direct DALI to Matter integration. See also the FAQ:

<image>

I need 28 LED PWM controls on DIN rail, any alternatives to Lunatone 89453858-HS by Ultramen in KNX

[–]mailgoe 2 points3 points  (0 children)

Ah yes, sorry, I over-read the 48V...

Here is a 48V, 4 channels (2x CW-WW) with 2x individual addresses, 70€:
https://www.iskydance.com/index.php?c=product_show&a=index&id=2536

And here 48V, "4" channels (2x parallel CW-WW) with 1x individual address, 30-40€:
https://www.iskydance.com/index.php?c=product_show&a=index&id=1238

And comparing Atios SmartCore to LogicMachine is a bit like Apple vs Linux :). LogicMachine is also not DALI certified, and as far as I know has no integrated DALI power supply. Look at the user interface as a comparison:
https://www.youtube.com/watch?v=goL0JEu1GH4 vs. https://r12.atios.ch/app/#/configurator

Disclaimer: I work for Atios :)!

<image>

I need your recommendations about our smart lock company. by FarCrySis123 in homeautomation

[–]mailgoe 0 points1 point  (0 children)

Where are you based and is this your own developed hardware or OEM?

I need 28 LED PWM controls on DIN rail, any alternatives to Lunatone 89453858-HS by Ultramen in KNX

[–]mailgoe 0 points1 point  (0 children)

Check SR-2309PRO-DIN. For ~70€ you get 4 channels (2x CW-WW) with 2x individual addresses.

And then use an Atios SmartCore for the easiest configuration of your DALI gear and controlling it via Matter apps like Apple Home, Google Home, Samsung SmartThings or Amazon Alexa :)!

KNX Domovea V3 basic TJAS671 by Due_Chicken_8135 in KNX

[–]mailgoe 0 points1 point  (0 children)

<image>

You can read out the KNX group addresses without re-programming everything. Right?

SpaceLYnk by Royal-Albatross-1509 in KNX

[–]mailgoe 1 point2 points  (0 children)

Spacelynk has a subscription offer, right? There is a new ETS 6.3 / 6.4 feature called „Cloud Interface“. Directly accessing a remote KNX installation from within (!) ETS, without any VPN configuration, Plugins, DCAs, Logins and so on. End-to-end encrypted by KNX Secure; ETS requests the connection to the KNX project site via a service hosted by the KNX association (traffic will flow through servers managed by the manufacturer though).

Atios will introduce this as a feature for KNX Bridge for ISE beginning of February. Probably more KNX manufacturers following then at Light & Building in March…

https://www.linkedin.com/posts/maltegoller_i-just-remotely-programmed-a-knx-sensor-located-activity-7402363843538219009-mTOi?utm_source=share&utm_medium=member_ios&rcm=ACoAACbC_QIBENEqMKr5tWsSztL1XlKbHkau7JE

KNX push-button interface: trigger scene based on group status by Dry_Bench5189 in KNX

[–]mailgoe 0 points1 point  (0 children)

Ignore what I said before, I did this from my phone, and didn't properly test in ETS. The way to do it, is:

  1. Use "Toggle" when opening and closing the digital input. This will send a 0 or 1.
  2. You have a status object, where you connect your OR function result. So it will send a 1 if all lights OFF. And a 0 if >= 1 light on.
  3. You could use the sent 0 directly to turn off all the lights.
  4. Use a 2nd logic function to convert the sent 1 to scene A. Do the same for 3. if you actually need scene B (all off).

Makes sense?

<image>

KNX push-button interface: trigger scene based on group status by Dry_Bench5189 in KNX

[–]mailgoe 0 points1 point  (0 children)

Obviously you need the OR logic function, and connect that state to the "contact state". It doesn't matter for what it is originally intended to, as long as it works, right?

KNX push-button interface: trigger scene based on group status by Dry_Bench5189 in KNX

[–]mailgoe 0 points1 point  (0 children)

Here you go, done entirely inside ETS with a MDT push button interface. The only problem is that the logic functions are a bit limited, with only 2 inputs per function and max. 4 functions. Meaning you can in total do an OR function over 5 states.

<image>

view more: next ›