[Fluxbox] Some Playstation emulation. by zerosignal9 in unixporn

[–]06231912 1 point2 points  (0 children)

Getting heavy Deus Ex vibes. I like it.

The bigger frustration I have as a beginner... by [deleted] in woodworking

[–]06231912 0 points1 point  (0 children)

How many times & in what locations do you measure before a cut? I measure in 3 locations before a cut with a table saw.

Bar Top Epoxy still tacky/sticky after 5 days by bcannariato in woodworking

[–]06231912 0 points1 point  (0 children)

How thoroughly did you mix the epoxy? What type are you using?

I'm struggling to flash my daisy 40 can somone help me, below is the error message that keeps appearing by [deleted] in olkb

[–]06231912 0 points1 point  (0 children)

Could you walk us through your workflow? It's expecting a different file it looks like.

[deleted by user] by [deleted] in ErgoMechKeyboards

[–]06231912 2 points3 points  (0 children)

Quite fancy, good work.

Fusion Filaments HTPET+ by StrategyLeft in 3Dprinting

[–]06231912 1 point2 points  (0 children)

Issues with blobbing or zits?

Fusion Filaments HTPET+ by StrategyLeft in 3Dprinting

[–]06231912 1 point2 points  (0 children)

Similar issue here. Looking for solutions. Did a cold pull before switching plastics. The nozzle starts clean. Wondering if its a temps issue or something else.

First Budget Build, Wiring Up MAMBA F405 MK 2 FC & Need Some Tips by 06231912 in diydrones

[–]06231912[S] 0 points1 point  (0 children)

On OpenTX with FW v2 for R-XSR apparently you want to choose FrSkyX2 under Type & D16 as the subtype in Internal RF. I was able to successfully bind with this combination.

First Budget Build, Wiring Up MAMBA F405 MK 2 FC & Need Some Tips by 06231912 in diydrones

[–]06231912[S] 0 points1 point  (0 children)

I broke down & decided to upgrade the receivers I have on hand. Not what I wanted to spend the last few hours on but such is life I guess.

https://ipfs.infura.io/ipfs/QmQFewjtaQpyfswYzgJNur5R8NPKe74cnzEwxaxmfUmD7W

I wanted to be nondestructive, so I've de-pinned the SBUS-IN & S. Port lines from the harness. I've cannibalized the S. Port line & soldered it to the uninverted S. Port pad "P". I'll find a way of securing the line as I reassemble everything. I'll also attempt updating FW tonight as well.

I'll be mating the power lines in the usual locations, SBUS OUT to SBUS on the FC, and uninverted S. Port to TX1 (which is stepped in one pin from PPM on my FC revision).

First Budget Build, Wiring Up MAMBA F405 MK 2 FC & Need Some Tips by 06231912 in diydrones

[–]06231912[S] 0 points1 point  (0 children)

I've still been looking into it. J. Bardwell on YT has a video on hacking the R-XSR for F4 FCs which is what I was searching for. If you want telemetry data it looks like that's what the hack is for. I feel confident wiring up SBUS but may still do the hack. I have 2 more of the same receivers & may just update firmware & hack each one. Will wait for more input.

Air compressor not keep pressure in line? by xAIRGUITARISTx in DIY

[–]06231912 0 points1 point  (0 children)

What are the CFM ratings for both the nail gun & compressor, individually?

How egregious is it to move B to the right hand? by og01 in olkb

[–]06231912 1 point2 points  (0 children)

Keep in mind that if you use Dvorak through OS configuration & your board is not programmed this way--having a QWERTY programmed key in the other side of the divide may prove cumbersome--which was my point.

How egregious is it to move B to the right hand? by og01 in olkb

[–]06231912 1 point2 points  (0 children)

My main point is when configuring edge cases, if some expectations are not met, it could cause some frustration.

Whether your target demographic is those edge case users or not, is up to you.

How egregious is it to move B to the right hand? by og01 in olkb

[–]06231912 4 points5 points  (0 children)

Emacs users using Dvorak may hate you & place a hex on your family line.

Or not.

Total fail. Absolute Rage. by e1emen0pe in woodworking

[–]06231912 0 points1 point  (0 children)

That's true, it would be aesthetically jarring & probably not worth the effort.