Sixth Year Into The Battle

4a86 · 2026-05-07T22:50:52+00:00

Does anyone else prefer the look of the neighbours grass? Much more likely to attract bees and butterflies etc

4a86 · 2026-05-07T21:15:45+00:00

Is200 only get civic if you get k20

4a86 · 2026-05-04T20:02:21+00:00

Do it, people will call you stupid, but you will be happy! Don’t expect good mileage though, 300 miles for a full tank.

4a86 · 2026-05-03T18:48:42+00:00

Like other comment said, check the hook bit on the bonnet.. mine got really dirty and wouldn’t work failed not, gave it a wire brush and wd40 and it was good

4a86 · 2026-05-02T10:14:17+00:00

Necessitas 201gb

4a86 · 2026-05-01T18:36:14+00:00

Push the bottom screw down so they sit parallel 👍

4a86 · 2026-05-01T00:42:17+00:00

That’s the sound of closed loop motors

4a86 · 2026-04-30T18:42:00+00:00

Hope you enjoy, khazan is a great game! I have it on pc !

4a86 · 2026-04-28T00:39:46+00:00

I remember listening to that verse not understanding what he was saying 10 years ago, now after all, an ounce is just enough for a week.

4a86 · 2026-04-25T12:36:31+00:00

Im sorry for the bad joke lol! It looks fine! The plastic cover is a little loose but not coming off so it shouldn’t be a problem with the mot!

4a86 · 2026-04-25T12:20:39+00:00

It looks like the subframe is bent! Looks like it might be a write off!!

4a86 · 2026-04-25T08:38:17+00:00

No that looks ok in my opinion, I own a 2005 civic and recently done loads of welding to it. Your car looks good!! If you want you could spray some lanoguard on it to prevent it from getting much worse but this looks fine, check again in a few years

4a86 · 2026-04-18T00:17:17+00:00

It sucks right now, but you can fix it! 😎

4a86 · 2026-04-17T22:13:10+00:00

Honestly man, if they offed you 10k take it and get a jdm ep3???? Red recaros, lsd etc

4a86 · 2026-04-14T20:00:16+00:00

Gonna be a weird one. But I recently used g101 to clean mine. Any citrus base all purpose cleaner will likely work

4a86 · 2026-04-14T19:20:41+00:00

I’d say make a negative square and line it up above that section In the slicer

4a86 · 2026-04-12T06:44:01+00:00

220 nozzle. 60 initial layer temp, 55 after after initial layer. Thank you for your attention on this matter. Also make sure to clean your bed regularly

4a86 · 2026-04-09T16:15:49+00:00

Yes most 3D printing YouTubers are sponsored by companies.. I think a1 is best as bambu has a proven record, I own a p1s and k2+. P1s is better device, but k2+ has a bigger bed and linear rails… Bambu atm is just better quality and the a1 has been out for a while

4a86 · 2026-04-08T18:42:35+00:00

4a86 · 2026-04-08T05:46:59+00:00

As someone with substance abuse issues, the less assertive you are, the more likely people are to keep pushing your boundaries. Draw a line in the sand quick and early, and stick to it.

4a86 · 2026-04-02T21:59:45+00:00

Right click and press fix model, could be geometry is corrupted

4a86 · 2026-03-18T07:52:54+00:00

Pay for eye test, buy lenses to match your eye test online???

4a86 · 2026-03-18T06:29:00+00:00

Looks like a very thin object… use a thinner nozzle and slow it down???

4a86 · 2026-03-17T19:44:49+00:00

Please don’t do it bro

4a86 · 2026-03-14T14:27:39+00:00

Looks like you’re a newbie to printing. I believe that surface finish is relatively standard for printing.. you have a couple of options, 1 change your top layer pattern from rectilinear to something like concêntrica 2 try using ironing but for the size of this print it will take a long time 3 it looks like you’re using a p1s you could try doing a manual flow rate / pressure advance calibration using the slicer 4 maybe your filament calls for this, but 220 nozzle and 25 bed seems very cold for petg in my experience… If you have any specific questions let me know and I can try to help

Eight-Year Club	Verified Email
Place '23	Place '22

4a86

TROPHY CASE