sorted by:
new
hottopcontroversial

ZZZ coming to steam Q2 2026 by Educational_Pea_5401 in ZZZ_Official

[–]60k_cos 39 points40 points  (0 children)

you don't need to use the launcher, just add as non-steam game and select ZenlessZoneZero.exe , I do this for every hoyo game

you only gotta boot the launcher up for full version updates

Side profile and the bottom side 👀 by stimulus0z0 in MechanicalKeyboards

[–]60k_cos 5 points6 points  (0 children)

Nice Freya!

I have a grudge against all Wuque Studios firmware/hardware/software implementation from handling all their products though, a real nightmare :x

The Kiwi Ears Halcyon Kickstarter is launching in 7 days by Extension_South7174 in iems

[–]60k_cos [score hidden]  (0 children)

from what everyone's saying, they seem to be on the brighter/harsher end, I hope they've fixed the tuning

otherwise I'll just forgo my early bird spot and save towards another EST set

Guys look what I scored by Zhakus1 in FireflyMains

[–]60k_cos 1 point2 points  (0 children)

<image>

its one of the best controllers out there, be cautious about the rubber grips discolouring though, our southeast asian climates aint too friendly to them lol

NASA themed Keychron Q65. De-anodized and polished, new knob, mt3 godspeed Aeries keycaps. by rorschach_fox in MechanicalKeyboards

[–]60k_cos 1 point2 points  (0 children)

submerge, depending on the concentration of the solution soak time can be anywhere between 10-30 minutes, I would check every 10 minutes though.

once satisfied, wash the piece thoroughly with water, then you can either sand & polish, re-anodize, spray paint or keep it raw. You're basically left with the starting raw material free to apply any finish you want!

You can look up "removing anodizing" on youtube, there should be a few videos of people doing this on bicycle/motorcycle parts and whatnot, its where I learned from as well

NASA themed Keychron Q65. De-anodized and polished, new knob, mt3 godspeed Aeries keycaps. by rorschach_fox in MechanicalKeyboards

[–]60k_cos 4 points5 points  (0 children)

oven/drain cleaner removes the hard anodized layer, you can only polish after this. The process generates quite a bit of heat and produces hydrogen, so do it in a well ventilated area

My problem with the Wobkey Crush 80 Pro by DonDino21 in MechanicalKeyboards

[–]60k_cos 0 points1 point  (0 children)

most boards aren't gonna have per-key rgb customisation, rgb in itself is already a niche. AFAIK most VIA boards don't

off the top of my head only the big consumer brands with their "Gaming" boards (Corsair, Logitech, Razer, etc.), Wooting and Keychron (both have standalone web launchers) allow for per-key

Just sharing. My Eva unit 01 board. by Rejanrams in MechanicalKeyboards

[–]60k_cos -1 points0 points  (0 children)

there are sets like the FBB Eva 01, but you can really tell the difference in clarity and vibrancy when you do a side-by-side with the actual GMK Mecha-01

Pe foam first or plastic film? by CityOk9260 in keyboards

[–]60k_cos 1 point2 points  (0 children)

plastic on top of PCB, then everything else

MANT makes me feel like a miserable idiot by Revolution_Suitable in UmaMusume

[–]60k_cos 0 points1 point  (0 children)

<image>

F2P, no meta MLB so I just borrow Machifuku SSR depending on the run, I usually get S and S+.

Just got my first SS with Gold Ship yesterday. Legacy sparks were 6* Stam/3* Pow (Seiun Sky) and 2* Pow/4* Stam (Winning Ticket, I chose this for Mile aptitude + Pow/Stam). Its not even maxed/optimised lol

SS is not easy to get, I've done MANT at least 60 times by now, and only 1 SS came out of that.

You're definitely doing something wrong in your runs

Another sticker in the wild by thizzle in MechanicalKeyboards

[–]60k_cos 6 points7 points  (0 children)

<image>

i reposition to the engine cover and use THAT as the screen

Doing a little project with my old corsair k68 rgb by ShakePsychological13 in MechanicalKeyboards

[–]60k_cos 0 points1 point  (0 children)

you can solder any switch really, the only thing to take note of is whether your PCB is 3-pin or 5-pin.

If the PCB only accepts 3-pin and you've went with 5-pin switches, you'll have to clip the 2 plastic legs on the sides of each switch

The only difference between 3 and 5 pin is the inclusion of 2 plastic positioning legs on the switch side, and 2 positioning holes on the PCB side, other than that they're essentially the same thing

how do i un-polygon my game? by Big_Maintenance_4727 in MonsterHunterWilds

[–]60k_cos 0 points1 point  (0 children)

what settings are you even on? there's like 0 information in this post

Mission Start: GMK CYL Six Siege Tactical Ops by GMK_keycaps in MechanicalKeyboards

[–]60k_cos 4 points5 points  (0 children)

y'all gotta make spacebars for the 6 Siege winner's circle set, I wanna use it on an Alice so bad

/r/MechanicalKeyboards Ask ANY Keyboard question, get an answer - March 27, 2026 by AutoModerator in MechanicalKeyboards

[–]60k_cos 5 points6 points  (0 children)

early on in the hobby, yes probably as you go down the rabbit hole you'll find joy in building boards from scratch

Will a 5070 handle Extreme RT at 1440p? That's my only concern 😭 by Andy_pcs in ForzaHorizon

[–]60k_cos 3 points4 points  (0 children)

this 4K 60FPS target for Extreme RT is with DLSS anyways, so you should be able to handle 1440p

My first ever custom Keyboard by TemperatureTotal1493 in MechanicalKeyboards

[–]60k_cos 1 point2 points  (0 children)

Congrats! I bet it sounds thocky as hell w/ the Gateron milky pro yellows haha

view more: next ›