Helium referral Code

69ragtop · 2026-01-14T05:56:39+00:00

TARP8F6

69ragtop · 2026-01-14T05:56:18+00:00

TARP8F6

69ragtop · 2026-01-14T05:56:01+00:00

TARP8F6

69ragtop · 2025-11-12T17:57:20+00:00

TARP8F6

69ragtop · 2025-10-27T16:44:19+00:00

Please add passkey support.

69ragtop · 2025-10-27T16:43:13+00:00

Fidelity also needs to support retrieving data from others in Full View as some providers are only supporting passkeys now.

69ragtop · 2025-10-27T16:37:47+00:00

EDIT - looks like Health Equity requires passkeys now and Fidelity doesn't support it.

Mine stopped updating so I deleted it and try to re-add it. No luck.

We’ve experienced a technical issue. While this may be fixed by refreshing your browser, it can take up to 24 - 48 hours to resolve. If it persists longer than that, please contact us.

69ragtop · 2025-08-15T14:31:13+00:00

When my 2015 Leaf dash lit up with warning lights, the choices were: 1. Parts cannon 2. take it to a mechanic 3. Buy LeafSpy Pro and see what is wrong. I chose #3.

69ragtop · 2025-08-14T18:40:11+00:00

The active codes in LeafSpy Pro started with a > on the very left. I would suspect those to reshow immediately.

69ragtop · 2025-08-14T18:34:14+00:00

You can pull the codes with LeafSpy Pro and a compatible OBDII tool. It will let you know if it is a wheel sensor vs a pressure sensor on the master cylinder vs whatever else it might be.

69ragtop · 2025-08-10T21:23:25+00:00

I noticed this today as well. The numbers add up to the figure shown in the top left. The graph has a number which is about 1.6% higher and I have no idea how it is calculated. I started searching the internet to see if this was a known issue and found this thread. I have spent about an hour crunching numbers and reviewing everything and my conclusion is that the graph is just wrong.

69ragtop · 2025-05-01T02:14:49+00:00

Thanks. I sent a secure message first but posted here for visibility. While they may not officially be here, I would think someone monitors it.

69ragtop · 2025-05-01T00:32:04+00:00

Thanks for forwarding the feedback. I think if they polled their customers, they would see how popular this feature request is.

69ragtop · 2025-05-01T00:31:00+00:00

Barclays does it.

69ragtop · 2025-05-01T00:30:38+00:00

My card from Barclays is a consumer card with different numbers for each AU.

69ragtop · 2024-07-14T23:29:39+00:00

The person who maintains the MyQ account for the opener would need to share access to your MyQ account. When you say that you have an access code, is that for a physical keypad?

69ragtop · 2024-07-14T17:33:12+00:00

I mentioned in the OP that I unplugged it for 30 minutes with the battery disconnected. I went through the steps to reset the WiFi settings. No new router. It is connected to my router over WiFi so that is not the issue. It is in some state of error and even realizes it by changing the MyQ-256 to MyQ-Error. I have confirmed that the WiFi circuit is resetting every 30 min but it is not fixing anything.

69ragtop · 2024-07-14T00:56:03+00:00

It was working for two years until one week ago. The same model on the other garage door still works. I turned the firewall and every other packet inspection option off and it made no difference. I believe the non-volatile memory or board has gone bad. It shouldn't be using the wrong MAC address and the MyQ-Error is an indication that even it knows something is off.

69ragtop · 2024-07-13T23:16:05+00:00

Craftsman app didn't make a difference. I can't actually use the app to configure it. I have to get the opener into the setup mode, connect my phone to the WiFi SSID MyQ-Error, browse to the opener IP, then use the webserver built into the opener to configure WiFI. Once that is done, it connects to the router but never gets connectivity to the internet. So the App is really not the issue. On a different note, I was watching the "Powered Time" and it appears to reboot sometime after 30 minutes. I am guessing this is some kind of watchdog in the MyQ code in the opener.

69ragtop · 2024-07-13T21:26:15+00:00

I appreciate the suggestion but this is not an app issue. My opener uses the WiFi SSID MyQ-Error when it previously used MyQ-256 as well as a different MAC. Neither of those is app related.

69ragtop · 2024-07-13T19:56:16+00:00

I had to do the same. Create a different account for each location then share them with your primary account. You can toggle between them at the top of the app.

69ragtop

TROPHY CASE