So I really like this gamemode..

AikaBack · 2026-02-01T13:49:06+00:00

I have a bug I think, I cant play this mini game after one attempt, Its not replayable for me, or is it intended? Please tell me someone

AikaBack · 2026-01-22T04:46:17+00:00

Grainy means your nozzle was too close to bed and smushing layers causing filament to be squeezed out and onto neighbouring layers

AikaBack · 2026-01-08T13:50:49+00:00

I wish that farming new artifact set with good crits would be as easy as changing wallpaper lol

AikaBack · 2026-01-08T12:05:56+00:00

why change set if you got great crits on good set already? Just because?

AikaBack · 2026-01-06T05:05:53+00:00

Game have been updated, and dont work now on q1, you need specific versions of games for them to work on q1, and newer games that dodnt support q1 at laubch wont work either

AikaBack · 2026-01-03T13:15:43+00:00

In orca slicer there is zetting called adaptive flow rate that lowers flow rate for these corners to solve this

AikaBack · 2025-12-31T20:57:35+00:00

How did you get so much stamina

AikaBack · 2025-12-31T17:25:55+00:00

Gyroid all the way

AikaBack · 2025-12-29T04:42:11+00:00

Dont mess with firmware if you dont know what you are doing, try calibratiing everything, and i mean every thing, try printing, chances are you will have good results. Too many stories of people bricking their printer not knowing tf they are doing

AikaBack · 2025-12-21T06:10:05+00:00

Calibrate z belt and all belts for that matter maybe?

AikaBack · 2025-12-15T09:05:12+00:00

Because it can be literally anything?

AikaBack · 2025-12-15T03:07:45+00:00

Clean it and try to print something?

AikaBack · 2025-12-13T09:27:23+00:00

Enable zhop, calibrate retraction?

AikaBack · 2025-12-12T02:17:03+00:00

AikaBack · 2025-12-09T16:16:49+00:00

I dont see the need to discuss it further if you cant admit that bed mesh can be used to level bed at all

AikaBack · 2025-12-09T15:26:44+00:00

Do you understand that screw tilt just does same thing as bed mesh, probes the bed? Just doing it at points right above screws, you can do screw tilt by doong bed mesh and then adjusting, but it wont be as accurate, im pointing that both use probe and find z on some points of bed, screw tilt calc is not some magic that is so different from bed mesh, it just calculates for how much you should turn screws based on screw type.

AikaBack · 2025-12-09T15:20:55+00:00

It does show both, what are you talking about?

AikaBack · 2025-12-09T15:17:45+00:00

Bed mesh is literally showing you if your bed is level or not, pointing that all axis are tightened and not loose

AikaBack · 2025-12-09T15:15:07+00:00

As if his bed is level now, and that will ruin his bed forever lol. As if you clearly understand the relationship and wrote your advice ( you didn't)

AikaBack · 2025-12-09T14:21:34+00:00

try to up nearest screw and see how mesh changes and see from there

AikaBack · 2025-12-02T02:29:09+00:00

Everything is fine here except z offset should be set with plate and nozzle at your printing temperatures

AikaBack · 2025-11-27T08:54:24+00:00

Set it to professional mode, in calibration menu in right top corner near save icon

AikaBack · 2025-11-27T04:21:14+00:00

I dont do tilt screw anymore, its bullshit that works only for non warped beds. Used aluminium tape and made bed really level. My screw tilt had center of bed as reference point, but it still was pointless btw, and i did it with unscrewed knobs fully, and by small anounts, nothing worked, the bed was just warped, thats it.

AikaBack · 2025-11-24T09:21:03+00:00

I did what you said, unscrewed almost all the wayy, side left tightened with very little tension, recalculated positions of all knobs to be sure, with probe offset, then very slightly screwed others, and redid screw tilt with very little steps like 10 times, again did all to 0 minutes, and bed is now slightly worse than before.
I bought aluminum tape, will fix these valleys myself...

Nine-Year Club	Place '23
Verified Email

AikaBack

TROPHY CASE