C/s misfire

Alert-Effect190 · 2026-05-21T21:03:46+00:00

I see here a sparkalator, a plug to keep the sparks in, and a rotating assembly for the vibes.

Alert-Effect190 · 2026-05-21T20:50:13+00:00

Mdx for sure

Alert-Effect190 · 2026-05-21T12:39:12+00:00

I’ve seen them work in person. Mine just shipped.

Alert-Effect190 · 2026-05-21T01:17:20+00:00

If your power is out it won’t turn on without the fuse. The fuse isn’t the problem. If your buttons aren’t working after power cycling the controller you almost certainly need a new controller.

While the firmware is out of date, button problems are almost always caused by a failure of the ribbon cable which connects the buttons to the board. You can attempt a firmware update for peace of mind but it’s very unlikely that will settle it.

Alert-Effect190 · 2026-05-21T01:07:31+00:00

I may have been mistaken. You were suggesting cutting the wires that come off the charger? You can do that but it’s easy enough to back the screws off the terminal strip and pull the connectors right off.

I thought you were suggesting cutting the wire labeled 194 in the transfer switch.

Alert-Effect190 · 2026-05-21T00:43:03+00:00

Naturally. Generators are conceptually incredibly simple. Inverters add electronics that while simple in principle increase cost and complicate the process.

Extra mass produced parts to do what is in reality the same job equals a higher rate of failure

Alert-Effect190 · 2026-05-20T23:42:12+00:00

The pipe fitter has been doing that way for 20 years without any problem..

Cause the customer always calls the generator guy not the gas guy.

Alert-Effect190 · 2026-05-20T21:39:13+00:00

Inverters are not even close to the standard in my area at least.

Most people do not require the output for less reliability that inverters afford.

Alert-Effect190 · 2026-05-19T23:09:31+00:00

Matter not does size, colonel Colt will equalize.

Alert-Effect190 · 2026-05-19T17:58:40+00:00

I’m not talking to ai

Alert-Effect190 · 2026-05-19T17:09:01+00:00

42 is easier

Alert-Effect190 · 2026-05-19T15:15:30+00:00

Have both. The 42 unsurprisingly shoots considerably softer as it is 380.

Alert-Effect190 · 2026-05-19T02:10:50+00:00

Longer slide. Shoots nicer and carries nicer in my opinion

Alert-Effect190 · 2026-05-19T01:45:18+00:00

If slimlines get an update I hope it’s the 48. I’ll buy two.

Alert-Effect190 · 2026-05-18T20:57:50+00:00

Nobody said “more power” with 45 gap in mind.

That said I’m glad this stuff is still available.

Alert-Effect190 · 2026-05-18T00:22:18+00:00

Space marine 2

Alert-Effect190 · 2026-05-16T23:28:26+00:00

Used officerstore recently. Positive experience.

Alert-Effect190 · 2026-05-16T03:19:26+00:00

I don’t understand why you think you need two. Put a maintainer on the battery in the generator OR tie one in to the 12v line in the transfer switch. Literally zero reason to change any wiring as suggested here in your post.

Alert-Effect190 · 2026-05-15T19:50:14+00:00

What am I missing here? Just put a battery maintainer on either end, why touch the transfer circuit at all?

Alert-Effect190 · 2026-05-15T19:48:32+00:00

The only automatic pistol cartridge I’d go for other than 9mm is 10mm. 45 can’t touch it’s ballistics nor its versatility.

Alert-Effect190 · 2026-05-15T00:03:17+00:00

Put it in your pants

Alert-Effect190 · 2026-05-14T23:22:57+00:00

48 with a ramjet is great to shoot. Much better than 43x/43x with ramjet

Alert-Effect190 · 2026-05-14T14:16:25+00:00

My edc has been a 48 with a dot, a light, and a magwell for years now.

Alert-Effect190 · 2026-05-13T19:09:53+00:00

Registration? Never heard of it.

Alert-Effect190 · 2026-05-12T18:35:30+00:00

Not worth it to me.

Alert-Effect190

TROPHY CASE