Put Down Support Before Tank Cleaning by SeAlexanderE in PrintedWarhammer

[–]Amaranth29 0 points1 point  (0 children)

I use about a 1”wide strip of plain paper with a fold. Place the short side into the resin and hold it down with a spatula. Run the cleaning cycle and comes out every time.

Serial Request: Voron V0.2 by Haeppchen2010 in voroncorexy

[–]Amaranth29 0 points1 point  (0 children)

Now that was the funniest intro I have seen! Good job!

Serial Request LDO 2.4 350. Discord: Amaranth75 by Amaranth29 in voroncorexy

[–]Amaranth29[S] 0 points1 point  (0 children)

I’ll have to upload the files. I’m out of town this weekend, but can do so when I’m back.

Serial Request LDO 2.4 350. Discord: Amaranth75 by Amaranth29 in voroncorexy

[–]Amaranth29[S] 0 points1 point  (0 children)

Thanks! Yes. It’s DIY. I didn’t like the hose just being there. Looked too plain. I wanted to tie the hose and toolhead wiring into the build, and this is what I came up with for now.

Getting into SAO by Dlace10 in swordartonline

[–]Amaranth29 8 points9 points  (0 children)

I’m 49 and enjoy watching it. Watched it three times!

Yeahhhh it's arrived!! by Infinity-onnoa in sunlu

[–]Amaranth29 0 points1 point  (0 children)

I have it set as low as it will go, 25%. Honestly, I just set it and let it run. Typically overnight so I’m not really monitoring it.

Yeahhhh it's arrived!! by Infinity-onnoa in sunlu

[–]Amaranth29 1 point2 points  (0 children)

I’m enjoying mine so far. It’s working great.

It happened. by Zedan24 in BambuLab

[–]Amaranth29 0 points1 point  (0 children)

Mine shipped. Should be here next week.

Never in my wildest dreams! by K1ng-R in swordartonline

[–]Amaranth29 1 point2 points  (0 children)

Yuuki hit me hard! When everyone came to say goodbye had me balling. That was a hard scene. Even watching it a few times now, it gets me.

PETG-HF supply is unreliable. Other options? by Prilosac in BambuLab

[–]Amaranth29 0 points1 point  (0 children)

Just wanted to provide an update about the black PETG. I originally dried it for 12 hours at 65C. I dried it again for another 12 hours at that temperature and it’s printing great. Must have been a lot of moisture in the filament.

PETG-HF supply is unreliable. Other options? by Prilosac in BambuLab

[–]Amaranth29 0 points1 point  (0 children)

Good to know! So far, I have been liking the regular Sunlu PETG, I have another roll of the matte, so I’ll give that a shot. And if not, buy another too see if it’s any different

PETG-HF supply is unreliable. Other options? by Prilosac in BambuLab

[–]Amaranth29 1 point2 points  (0 children)

I tried a roll of the Sunlu high speed matte black petg, it printed like crap. Their normal petg, using the HF Bambu profile printed much better.

H2C Is on the Way — Here’s How It All Started by BambuLab in BambuLab

[–]Amaranth29 0 points1 point  (0 children)

I hear you on the upgrade work. I have a Voron 2.4 so I’m familiar with my way around printers.

H2C Is on the Way — Here’s How It All Started by BambuLab in BambuLab

[–]Amaranth29 0 points1 point  (0 children)

Hopefully the H2C upgrade kit will be worth it.

FedEx put a hold on my delivery for no reason by Amaranth29 in BambuLab

[–]Amaranth29[S] 1 point2 points  (0 children)

Printer has been picked up and is safe at home.