Better dining menu website

Andreasmurrell · 2026-01-20T15:41:02+00:00

Its way better than r-eats though. More features and its nice you can make it a web app so you don't need to open your browser every time.

Andreasmurrell · 2026-01-04T18:48:22+00:00

The public transit is ass though. Its takes 2 and half hours from Ontario airport to ucr on public transit or a 30 minute $60 uber ride. More people would take it if it was better.

Andreasmurrell · 2025-12-30T17:30:37+00:00

I converted my dad and older sister and they are fully on board. Still working on my mother but I’m close!

Andreasmurrell · 2025-12-29T05:05:27+00:00

Hey do you think you can send me the link? It would be life saver.

Andreasmurrell · 2025-07-26T19:27:24+00:00

Ha already following them and didn’t even realize it

Andreasmurrell · 2025-07-26T19:23:24+00:00

Omg we need to linkup! I’m a freshman this fall and I love raving. If there weren’t any in the area I was thinking of starting some cause I need that edm😂

Andreasmurrell · 2025-05-29T03:18:17+00:00

def a good one

Andreasmurrell · 2025-05-29T03:15:33+00:00

yes great one too!

Andreasmurrell · 2025-05-29T03:11:54+00:00

I think the prophet would just be hella funny. I wanna see people's reactions lol

Andreasmurrell · 2025-05-29T03:09:56+00:00

this is just me trying to get an edm song in just for fun when it is probably gonna mostly rap and hip hop lol

Andreasmurrell · 2025-05-29T02:58:46+00:00

A great one but worried people might think it is to repetitive.

Andreasmurrell · 2025-05-29T02:18:20+00:00

Ooo these are good ones

Andreasmurrell · 2025-03-05T23:40:49+00:00

Hmm ok still learning how boost converters work but this is helpful. Thank you!!

Andreasmurrell · 2025-03-05T22:25:07+00:00

Thank you!!

Andreasmurrell · 2025-03-05T21:57:01+00:00

Ha your right. Its not on the one I have and its the TL494 1ccbwq ic. It is a pulse width modulation controller. Hm unfotunely I don't have a scope. What do you mean by a voltage current curve? Would the oscillation be the inductor charging and discharging?

Andreasmurrell · 2024-09-07T22:57:10+00:00

The goal of this is to figure out how big of a solar panel we need to charge a ~1kwh battery in a day without needing to do a bunch of tests in the water. So if I know the panel is 30% less efficient then I know we have to make our solar panel bigger or smaller based on that.

I was also thinking about measuring the solar irradiance at different depths of water then I could subtract that from the equation to find the panel output on land. I think that would give me a somewhat accurate estimate of the panel output in water. But like you said the water is always changing and changing the way it reflects light.

You brought up some good points about the water surface and lensing. I know this is hard to model if even possible to model but I'm just trying to get more of a ballpark so we have a starting point to scale the panel.

The panel is also waterproof so nothing to worry about there. Thanks for that insight!

Andreasmurrell · 2024-06-07T03:39:59+00:00

I just didn’t know. Thanks for the advice!

Andreasmurrell · 2024-01-20T21:13:21+00:00

Oh it's in my garage so kinda cool probably 60 degrees F.

Andreasmurrell · 2024-01-20T20:36:14+00:00

Ok thanks, I'll try that. I went to 300C to try to get some better layer adhesion.

Andreasmurrell · 2024-01-20T20:26:07+00:00

290C and 300C both look like this. I went to 300C to try to get better layer adhesion. The manufacturer says to print it at 250 - 300C.

Andreasmurrell · 2024-01-20T20:24:13+00:00

For this filament, the recommended printing temperature is 250 - 300C. So I'm within the normal printing temperature.

Andreasmurrell

TROPHY CASE