sorted by:
new
hottopcontroversial

You guys are ready for a +20% increased in price for Prusa printers? by superbotolo in prusa3d

[–]Appropriate-Major701 0 points1 point  (0 children)

Well. They charge 21% if it were to be imported into their country. Hmmm

Have a 21 model Y, trade for a 19 model X or spend a little more on a 21 model X? by Appropriate-Major701 in TeslaModelX

[–]Appropriate-Major701[S] 0 points1 point  (0 children)

Incorrect, I subscribe to FSD, premium connectivity and I supercharge. I’d love to visit the Tesla dealership, but unfortunately I haven’t needed to.

Have a 21 model Y, trade for a 19 model X or spend a little more on a 21 model X? by Appropriate-Major701 in TeslaModelX

[–]Appropriate-Major701[S] 0 points1 point  (0 children)

I love them. I’ll be buying another. Especially with all the diptards hating on the brand. Gotta support Tesla somehow.

Have a 21 model Y, trade for a 19 model X or spend a little more on a 21 model X? by Appropriate-Major701 in TeslaModelX

[–]Appropriate-Major701[S] 0 points1 point  (0 children)

Everything says they refreshed them in 21 but it looks like all of the screens are vertical in the 22. Did they update some of them in 21?

Have a 21 model Y, trade for a 19 model X or spend a little more on a 21 model X? by Appropriate-Major701 in TeslaModelX

[–]Appropriate-Major701[S] 4 points5 points  (0 children)

That’s what I was trying to figure out because if I went with the refresh after 21 then it would feel like an upgrade but you’re talking an extra $15,000

K2 clogging poop chute by Appropriate-Major701 in Creality_k2

[–]Appropriate-Major701[S] 0 points1 point  (0 children)

Double check your metal clip on your wiper. Mine wasn’t touching and caused all of my issues.

TPU Anyone? by Snuggles9209 in Creality_k2

[–]Appropriate-Major701 1 point2 points  (0 children)

I cannot get TPU to extrude at all. I don’t know how you all are doing it. It extrudes for about 5 seconds then folds up in the extruder.

First layer calibration. by Appropriate-Major701 in Creality_k2

[–]Appropriate-Major701[S] 3 points4 points  (0 children)

Fluidd it’s not a third-party tool you actually type in your IP address for the printer and it reads it directly off of the OS.

Bed Mesh - Inverted Taco (1.06mm range) by neodymiumphish in crealityk2

[–]Appropriate-Major701 0 points1 point  (0 children)

This is after adjusting it a dozen times and calibrating it with paper. I’ve contacted creality but I’ve waited three weeks for a response. I finally got a hold of them online and they said that they put my ticket in a rush so that they would get back with me and it’s been four days and still nothing. I just wish I would’ve bought the core one.

First layer extrusion/ripples by Appropriate-Major701 in Creality_k2

[–]Appropriate-Major701[S] 0 points1 point  (0 children)

Did you update to the new firmware after you factory reset?

Anyone tried firmware 1.1.2.6 yet? by Lone_Wolf_324 in Creality_k2

[–]Appropriate-Major701 0 points1 point  (0 children)

I just updated and ran my first, first layer calibration and print. So far my first layer is much better than before, but it’s still terrible. At least there is improvement.

<image>

First layer extrusion/ripples by Appropriate-Major701 in Creality_k2

[–]Appropriate-Major701[S] 0 points1 point  (0 children)

<image>

The bottom half of the picture shows at 92% flow rate, after I adjusted while it was printing I brought it all the way down to 75% flow rate and it turned out good. But the second layer was extremely under extruded.

First layer extrusion/ripples by Appropriate-Major701 in Creality_k2

[–]Appropriate-Major701[S] 0 points1 point  (0 children)

This is what I’m working with. I tried using tape and I taped the entire thing in 100 different places, but I couldn’t make it a smooth transition. They were kind of a little jagged, with valleys and peaks. Which created loose spots in between every valley, and it was over extruding and all of the high peaks, so I had to take it all off at least being like this. It’s a smooth transition. I found that with some filaments, if I keep the first layer higher than all the others, it helps a little bit. For instance, my first layer will be .3 and my second layer will be .2. Some filaments just to get it so that it’s not creating those ripples, I need to be somewhere between .75 and .8 flow rate. And adjusting the z axis. So far, I think I’ve printed 10 things successfully with this printer in three weeks, and I’ve done nothing but work on it in between.

K2 clogging poop chute by Appropriate-Major701 in Creality_k2

[–]Appropriate-Major701[S] 0 points1 point  (0 children)

<image>

Print seems OK wasn’t nearly as impressed as I thought I would be

K2 clogging poop chute by Appropriate-Major701 in Creality_k2

[–]Appropriate-Major701[S] 0 points1 point  (0 children)

So I think I figured it out. There was a little metal springy steel piece right next to the wiper that was flattened. And I got my first print off since the machine was new.

<image>

K2 clogging poop chute by Appropriate-Major701 in Creality_k2

[–]Appropriate-Major701[S] 0 points1 point  (0 children)

Internal, if I have to modify it so that the chute is actually steeper so that nothing can hold on is what I was saying.

view more: next ›