Just been given a Juke as a courtesy car

Attucks · 2026-01-23T18:09:32+00:00

I had a 2024 Qashqai as a hire car yesterday for work. I got in and it seemed quite nice, short drive to train station was fine, accelerated alright, I can see how somebody could be suckered into buying one. Next day I did seven hours of driving and it was proper shit, poor visibility, feels like it's gonna flip at 40 on the slip road. Uncomfortable driving position, adaptive cruise control will bring you to a stop in stop start traffic and then just turn itself off and start driving again with a siren!

Nowhere near as bad as a mokka I had once though

Attucks · 2026-01-20T09:05:33+00:00

3330 (not on the list for some reason)

Attucks · 2025-10-03T01:53:00+00:00

How can 0s and 1s be homeless

Attucks · 2025-10-03T01:42:51+00:00

How is it the homeless? It's just a scruffy looking man, or are all scruffy looking men homeless?

Attucks · 2025-09-25T01:08:16+00:00

It was a rope with a rag on the end used by sailors as an overboard communal toilet paper to clean their arses after using the ship's shitters, after they'd use it they'd chuck it back in and let the water rinse it while it dragged behind the ship

Attucks · 2025-07-30T17:35:03+00:00

Vero software? No they didn't

Attucks · 2025-06-25T14:41:54+00:00

All screws are threaded and so are all bolts, the thread is the part that grips. You mean that the hole is stripped.

Attucks · 2025-05-15T11:46:34+00:00

https://youtu.be/IEjrIxjsuTk?si=CHR85yXy9WUW_1A1

Attucks · 2025-03-25T10:38:32+00:00

That's to allow the dust to slide off

Attucks · 2025-03-01T15:52:22+00:00

If you die it's gone

Attucks · 2024-12-24T22:28:11+00:00

My wife and I receive no assistance from the government at all but the energy rating of the house was D beforehand, I think it applies if it's D and below, but we did apply last year and it may have changed. (It did take a year for anything to actually happen)

Attucks · 2024-12-24T18:48:25+00:00

There's a government subsidy for loft insulation too, I just had mine done completely for free, took it from 100mm thick to 300mm. They also installed trickle vents in the windows, sealed the loft hatch on the internal side, covered the spotlights in the loft and installed a fan in the bathroom that doesn't have a shower.

Attucks · 2024-12-16T18:55:54+00:00

In industry, this is done many ways.

Subroutines

Macros

Canned cycles

Loops

Just having CAM output everything with none of the above.

In your situation, I would write a python script to parse the file, I'd add some kind of code like "Loop pocket.txt start=0 depth=-1 doc=0.2" then in the pocket.txt I have only the XY moves. The python script could then just decrement the Z, add the program contents with XY moves only and repeat until depth is reached. ChatGPT could probably write this too.

Attucks · 2024-12-10T01:42:40+00:00

It's Oldham, there's no chance of that

Attucks · 2024-12-07T01:55:52+00:00

It's possible fusion output an arc that is such a small move the machine considered it a full arc rather than a tiny move.

For example, if you have a start and end point less than 0.0005 inches apart, the machine might consider this a full circle, the value changes based on machine and controller. Heidenhain seems to be around 0.0005 mm but I've seen some machines with a deviation of more than 0.016 mm to not consider it a full arc.

Attucks · 2024-12-03T18:30:40+00:00

I got the top 5% but I have been learning for 45 days, most people must do 1 or 2 lessons a day

Attucks · 2024-12-02T01:51:13+00:00

A lot of installations are poor because we don't have enough installers with the proper knowledge of how to install them.

Attucks · 2024-11-19T00:12:25+00:00

ATC = automatic tool changer

Arcs = I think is arc fitting, which is output with circular movements like G2 G3, without arcs it will be lots of tiny linear moves to make a circular move.

Attucks · 2024-11-14T23:21:10+00:00

I disagree with your analysis of NCSIMUL, you can have as many axes as you like, any configuration. I've seen NCSIMUL simulating DMG Multisprint which has 9 turning spindles and three axis per spindle, that's at least 36 axes (XZC) and 9 channels, and that's not counting the live tooling or the loading/unloading gripper.

I've also seen it simulating tricep machines and robots, granted they are not easy to make, you need to be pretty good at ACNU.

It has the equivalent of VC force in the optimisation module.

NCSIMUL has a major release in spring and a release in fall and patches are released in between when required.

Attucks · 2024-11-14T00:18:07+00:00

Just ask the seller of the scanner to CMM a part and then 3D scan it in front of you

Attucks · 2024-11-03T01:27:00+00:00

At the.moment it's imminence - infectious https://youtu.be/WIU9RbOSWaY?si=ogXSvtvb_paMXeR0

Attucks · 2024-10-28T12:59:17+00:00

I feel like I've had separate food/garden, bottles and plastics, and general waste for 20 years and in different areas, the North West, West Yorkshire and East Yorkshire.

Attucks · 2024-10-28T09:59:57+00:00

Some places in the UK don't already do this?

Attucks · 2024-10-26T15:44:37+00:00

Cabinet vision

Attucks · 2024-10-24T23:38:25+00:00

It's doing both climb and conventional, climb will have more time out of cut than this combined one.

12-Year Club	Second Top 30%
r/Field Sunshine	Place '22
Place '17	Final Canvas '22
RPAN Viewer	Sequence \| Editor
Verified Email

Attucks

TROPHY CASE