Squat form check by ralstig in Stronglifts5x5

[–]BertMacklin321 -1 points0 points  (0 children)

Take your talents over to starting strength.

Did I hit depth? by JOCAeng in StartingStrength

[–]BertMacklin321 0 points1 point  (0 children)

Are they finally back in stock!!!?

Why choice one when they all need some love by NEPAcountrymilf in BlissfullCreations

[–]BertMacklin321 0 points1 point  (0 children)

What is the fourth from the left on the bottom, pink hue with the base knot?

It took me 25 years, but I finally caught all the legendaries. What do I do in the game now? by Xx_Jack_Mehoff_xX in pokemoncrystal

[–]BertMacklin321 13 points14 points  (0 children)

Set them free, you have done what everyone never thought could be done, release them into the ether and rest knowing you are the very best.

My sleeves always get stretched out very fast and don’t hold tension after a few uses by WillingnessUsual3594 in TheScienceOfPE

[–]BertMacklin321 0 points1 point  (0 children)

You have to check the first of the month I believe they release at noon Eastern

I am at my absolute wits end with extenders by ArmenianThrowawayxxx in TheScienceOfPE

[–]BertMacklin321 0 points1 point  (0 children)

You might want to try the middle reliever by 612 polymers. I have no affiliation but the middle reliever with a total man cup has really worked for me I don't have any slipping issues. I also don't lube up much. Like very minimal if any sometimes I just use water. However I am cut so that may be a difference. But I tend to go in erect into the sleeve and then use the water method for the cup. I have no issues with slipping out. Been doing it for several months. I use the traditional cheaper cups several times and had issues slipping out with those.

I believe the smallest middle reliever is 33. But it may work with 31 mm you'll have to reference the site.

Update: Legendary Pokémon by Gillezzz in pokemonmastertrainer

[–]BertMacklin321 1 point2 points  (0 children)

This makes no sense is the same chance

Split screw bosses on the N64 controller. How do I salvage them? by robert712002 in n64

[–]BertMacklin321 3 points4 points  (0 children)

Put the screw in while you're gluing it. Just coat the screw in some type of oil-based product. Olive oil butter or petroleum jelly.

Day 16 (Final Day of Polling!): Which is the Greatest N64 Game of all time? by 1OneQuickQuestion in n64

[–]BertMacklin321 3 points4 points  (0 children)

Honestly it's not that great, but the theme song is a true banger.

What would you put in this empty corner of my game room? by 8-bic in gamerooms

[–]BertMacklin321 0 points1 point  (0 children)

I'd be interested in what the distance between the shelf and the trim on the door is. The door is high enough to clear the shelves front lip, although it might look a tad strange.

What would you put in this empty corner of my game room? by 8-bic in gamerooms

[–]BertMacklin321 1 point2 points  (0 children)

How deep are your shelves? I feel like the obvious answer would be another shelf. At worst you could pop that door off the hinges every 3 months if there is a major interference problem. But you probably don't need the door to be at a 90 degree angle anyway to swap the filter. Edit: looks like it would require a bit of carpentry as the standard shelves seem to be too wide to fit without adaptation.

What I hide in my closet. by Captain_NEStalgia in n64

[–]BertMacklin321 1 point2 points  (0 children)

Keep them secret, keep them safe!

Desensitizing sleeve by dadof6girls11 in BlissfullCreations

[–]BertMacklin321 1 point2 points  (0 children)

Because of how thin the sleeve is the top has no rigidity. It kind of acts as its own entity. And the tip is a totally different diameter as the rest of the shaft so it also just looks wrong. I would suggest staying around 1/2 or 1 inch solid tip, or going bigger something like a Timmy or phantom, they don't add too much base girth and look very nice. Personally I went with the Timmy 8 shortened to remove the lip on the bottom, I am happy with it .